Husqvarna 1130SB-XLSB owner manual Troubleshooting

Page 19

TROUBLESHOOTING

See appropriate section in manual unless directed to a qualified service center.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition key

2.

Insert safety ignition key.

 

 

is not inserted.

 

 

 

3.

Out of fuel.

3.

Fill fuel tank.

 

4.

Throttle in STOP position.

4.

Move throttle to FAST position.

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Drain fuel tank and carburetor, refill tank with fresh gasoline.

 

11.

Water in fuel.

11.

Drain fuel tank and carburetor, refill tank with fresh gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Drain tank and refill with fresh, clean fuel.

 

4.

Water in fuel.

4.

Drain fuel tank and carburetor, refill tank with fresh gasoline.

 

5.

Carburetor is in need of

5.

Contact a qualified service center.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts.

vibration

 

augers or impeller.

 

If vibration remains, contact a qualified service center.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact a qualified service center.

 

 

(if so equipped)

 

 

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 1130SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Rotator Head Mounting Chute Deflector Remote ControlParts Packed Separately in Carton EXT RA Shear Bolts and NutsUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USESnow Thrower CleaningEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingCARRIAGEBOLT5/16−18X.750 Weight BAR532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP RivetRotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator HeadHandles POP Rivet 1/8 01.12.002-C 532 17 86-66 Halogen Headlight Grip Switch532 42 13-51 Console Panel Gray 532 42 14-48 Headlight Bezel GrayClik PIN DriveAxle Shaft Thrust Washer921 01.02.002-F Clevis PIN 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Idler Pulley01.01.001-B 532 42 38-70 Engine Mount Plate Chassis / Engine / PulleysFrame Bottom PANSteer Cable Bracket RH Wheel Assembly LHWheels Steer Cable Bracket LHAxle Lobe CoverWheel Lobe SpringRetainer PIN Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY BAG of Parts532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement

1130SB-XLSB specifications

The Husqvarna 1130SB-XLSB is a powerful snow blower designed to tackle even the most challenging winter conditions. This robust machine delivers professional-grade performance for homeowners and property managers alike. With its impressive engine, advanced features, and user-friendly controls, it stands out as a top choice in the market.

At the heart of the Husqvarna 1130SB-XLSB is a powerful 291cc engine that utilizes a reliable electric start system. This means users can quickly and easily start the snow blower without the hassle of traditional pull starts. The machine is equipped with a durable 30-inch clearing width, allowing for efficient snow removal from driveways, sidewalks, and larger areas in a single pass. Coupled with a 23-inch intake height, it is capable of handling heavy, compacted snow and ice with ease.

The advanced technology incorporated into the Husqvarna 1130SB-XLSB sets it apart from the competition. One notable feature is its hydrostatic transmission, which provides seamless and infinitively variable speed control. This allows operators to adjust the speed according to different snow conditions and personal preferences, enhancing maneuverability and control.

The snow blower also features an adjustable discharge chute, which can rotate 200 degrees, allowing users to direct the expelled snow precisely where they want it. This is particularly useful in varying landscaping conditions, ensuring minimal disruption to surrounding areas.

For added convenience during nighttime operations or in low-light conditions, the Husqvarna 1130SB-XLSB includes bright LED headlights, ensuring visibility and safety. It also boasts heated hand grips, allowing operators to work comfortably even in the coldest weather conditions.

Additionally, the snow blower's rugged construction is designed to withstand harsh winter elements. It features sturdy steel components and an enhanced auger system that can cut through heavy snow efficiently. The tires are designed with excellent traction, providing stability and control on icy surfaces.

In summary, the Husqvarna 1130SB-XLSB snow blower combines power, performance, and innovative technology. With its strong engine, hydrostatic transmission, adjustable chute, and thoughtful ergonomic features, it is perfectly equipped to handle the most difficult winter challenges, making snow removal a more manageable task for anyone.
Top Page Image Contents