Husqvarna 1130SB-XLSB owner manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and work- ing.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16.Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manu- factured to give best possible dependability and perfor- mance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity

4.0 Quarts (3,79 Liters)

and Type:

Unleaded Regular only

 

 

Oil Type

SAE 5W-30 or 10W-30

(API SG–SL):

(0°F to +40°F / –18°C to +5°C)

 

Synthetic SAE 5W-30 or 10W-30

 

(below 0°F / –18°C)

 

 

Oil Capacity:

28 Ounces (0,8 Liters)

 

 

Spark Plug:

Champion QC12YC

Gap:

0.030" (0,762 mm)

 

 

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

PRODUCT SPECIFICATIONS

3

CUSTOMER RESPONSIBILITIES

3

ASSEMBLY / PRE-OPERATION

5-7

OPERATION

8-14

MAINTENANCE SCHEDULE

14

MAINTENANCE

14-15

SERVICE AND ADJUSTMENTS

16-18

STORAGE

18

TROUBLESHOOTING

19

REPAIR PARTS

20-39

3 WARRANTY

BACK COVER

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 1130SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Rotator Head Mounting Chute Deflector Remote ControlParts Packed Separately in Carton EXT RA Shear Bolts and NutsUnfold Upper Handle Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR See Fig To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USECleaning Snow ThrowerEngine Shear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingCARRIAGEBOLT5/16−18X.750 Weight BAR532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP RivetRotator Pivot Bracket 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator HeadHandles POP Rivet 1/8 01.12.002-C 532 17 86-66 Halogen Headlight Grip Switch532 42 13-51 Console Panel Gray 532 42 14-48 Headlight Bezel GrayClik PIN DriveAxle Shaft Thrust Washer921 01.02.002-F Clevis PIN 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Idler Pulley01.01.001-B 532 42 38-70 Engine Mount Plate Chassis / Engine / PulleysFrame Bottom PANSteer Cable Bracket RH Wheel Assembly LHWheels Steer Cable Bracket LHAxle Lobe CoverWheel Lobe SpringRetainer PIN Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY BAG of Parts532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement

1130SB-XLSB specifications

The Husqvarna 1130SB-XLSB is a powerful snow blower designed to tackle even the most challenging winter conditions. This robust machine delivers professional-grade performance for homeowners and property managers alike. With its impressive engine, advanced features, and user-friendly controls, it stands out as a top choice in the market.

At the heart of the Husqvarna 1130SB-XLSB is a powerful 291cc engine that utilizes a reliable electric start system. This means users can quickly and easily start the snow blower without the hassle of traditional pull starts. The machine is equipped with a durable 30-inch clearing width, allowing for efficient snow removal from driveways, sidewalks, and larger areas in a single pass. Coupled with a 23-inch intake height, it is capable of handling heavy, compacted snow and ice with ease.

The advanced technology incorporated into the Husqvarna 1130SB-XLSB sets it apart from the competition. One notable feature is its hydrostatic transmission, which provides seamless and infinitively variable speed control. This allows operators to adjust the speed according to different snow conditions and personal preferences, enhancing maneuverability and control.

The snow blower also features an adjustable discharge chute, which can rotate 200 degrees, allowing users to direct the expelled snow precisely where they want it. This is particularly useful in varying landscaping conditions, ensuring minimal disruption to surrounding areas.

For added convenience during nighttime operations or in low-light conditions, the Husqvarna 1130SB-XLSB includes bright LED headlights, ensuring visibility and safety. It also boasts heated hand grips, allowing operators to work comfortably even in the coldest weather conditions.

Additionally, the snow blower's rugged construction is designed to withstand harsh winter elements. It features sturdy steel components and an enhanced auger system that can cut through heavy snow efficiently. The tires are designed with excellent traction, providing stability and control on icy surfaces.

In summary, the Husqvarna 1130SB-XLSB snow blower combines power, performance, and innovative technology. With its strong engine, hydrostatic transmission, adjustable chute, and thoughtful ergonomic features, it is perfectly equipped to handle the most difficult winter challenges, making snow removal a more manageable task for anyone.
Top Page Image Contents