Husqvarna 1130SB-XLSB owner manual Assembly / PRE-OPERATION, Remove Snow Thrower from Carton

Page 5

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower. Reading the entire manual will familiarize you with the unit, which will assist you in assembly, operation and maintenance of the product.

Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your snow thrower, all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness.

REMOVE SNOW THROWER FROM CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut down all four corners of carton and lay panels flat.

3.Remove the two (2) screws securing the auger housing to the pallet.

4.Remove all packing materials except plastic tie holding speed control rod to lower handle.

5.Remove the two (2) plastic ties securing the upper handle to the pallet.

6.Remove snow thrower from carton and check carton thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 10)

A toolbox is provided on your snow thrower. The toolbox is located on top of the belt cover. Store the extra shear bolts, nuts and multi-wrench provided in parts bag in the toolbox.

NOTE: The multi-wrench may be used for assembly of the chute rotator head to snow thrower and making adjustments to the skid plates.

UNFOLD UPPER HANDLE

1.Raise upper handle to the operating position and tighten handle knobs securely. Additional carriage bolts, washers and handle knobs are in bag of parts. Use to secure upper handle to lower handle. Install in lower holes in handles.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

1.Remove plastic tie securing rod to lower handle.

2.Insert rod into speed control bracket and secure with retainer spring.

SPEED

CONTROL

ROD

PLASTIC TIE

UPPER

HANDLE

HANDLE

KNOB

LOWER

HANDLE

FIG. 1

SPEED CONTROL ROD

 

RETAINER

 

SPRING

SPEED

SPEED

CONTROL

CONTROL

BRACKET

LEVER

Fig. 2

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 1130SB-XLSb Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Chute Deflector Remote ControlEXT RA Shear Bolts and Nuts Rotator Head MountingHOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYDrive speed control lever used to select forward or Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigScraper BAR See Fig Before Starting the EngineTo USE Drift Cutters See Fig Check Engine OIL Level See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningSnow Thrower To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Assembly 30 RH Auger Assembly 30 LHSkid Plate Auger Ball BearingCARRIAGEBOLT5/16−18X.750 Weight BARKnob Black Control Panel / Discharge ChutePOP Rivet 532 42 17-28 Shield Retainer StrapCable Assembly Gray 532 42 11-60 LEVER/CABLE Rotator Assembly GrayRotator Head Rotator Pivot BracketHandles POP Rivet 1/8 01.12.002-C 532 42 13-51 Console Panel Gray Grip Switch532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightAxle Shaft DriveThrust Washer Clik PIN921 01.02.002-F 532 18 77-86 Traction Idler ARM 532 18 04-78 Engine Traction PulleyIdler Pulley Clevis PIN01.01.001-B Frame Chassis / Engine / PulleysBottom PAN 532 42 38-70 Engine Mount PlateWheels Wheel Assembly LHSteer Cable Bracket LH Steer Cable Bracket RHWheel Lobe CoverSpring Axle LobeKEY Part Description 532 19 30-71 Safety Ignition KEY Power CordBAG of Parts Retainer PIN532 18 10-35 DECAL, DANGER, Deflector DecalsWarranty Statement

1130SB-XLSB specifications

The Husqvarna 1130SB-XLSB is a powerful snow blower designed to tackle even the most challenging winter conditions. This robust machine delivers professional-grade performance for homeowners and property managers alike. With its impressive engine, advanced features, and user-friendly controls, it stands out as a top choice in the market.

At the heart of the Husqvarna 1130SB-XLSB is a powerful 291cc engine that utilizes a reliable electric start system. This means users can quickly and easily start the snow blower without the hassle of traditional pull starts. The machine is equipped with a durable 30-inch clearing width, allowing for efficient snow removal from driveways, sidewalks, and larger areas in a single pass. Coupled with a 23-inch intake height, it is capable of handling heavy, compacted snow and ice with ease.

The advanced technology incorporated into the Husqvarna 1130SB-XLSB sets it apart from the competition. One notable feature is its hydrostatic transmission, which provides seamless and infinitively variable speed control. This allows operators to adjust the speed according to different snow conditions and personal preferences, enhancing maneuverability and control.

The snow blower also features an adjustable discharge chute, which can rotate 200 degrees, allowing users to direct the expelled snow precisely where they want it. This is particularly useful in varying landscaping conditions, ensuring minimal disruption to surrounding areas.

For added convenience during nighttime operations or in low-light conditions, the Husqvarna 1130SB-XLSB includes bright LED headlights, ensuring visibility and safety. It also boasts heated hand grips, allowing operators to work comfortably even in the coldest weather conditions.

Additionally, the snow blower's rugged construction is designed to withstand harsh winter elements. It features sturdy steel components and an enhanced auger system that can cut through heavy snow efficiently. The tires are designed with excellent traction, providing stability and control on icy surfaces.

In summary, the Husqvarna 1130SB-XLSB snow blower combines power, performance, and innovative technology. With its strong engine, hydrostatic transmission, adjustable chute, and thoughtful ergonomic features, it is perfectly equipped to handle the most difficult winter challenges, making snow removal a more manageable task for anyone.
Top Page Image Contents