Husqvarna 927SBEXP owner manual How To Use Your Snow Thrower, Operation, Stopping

Page 10
HOW TO USE YOUR SNOW THROWER

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

STOPPINGTO USE FUEL SHUT-OFF VALVE (See Fig. 11)TO USE THROTTLE CONTROL (See Fig. 12)TO USE CHOKE CONTROL (See Fig. 13)TO CONTROL SNOW DISCHARGE (See Fig. 14)Manual background safety glasses or eye shields while operating your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

•Release the auger control lever to stop throwing snow.

ENGINE

1.Move throttle control to “STOP” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE FUEL SHUT-OFF VALVE (See Fig. 11)

The fuel shut-off valve is located beneath the fuel tank on the engine. Always operate the snow thrower with the fuel shut-off valve in the OPEN position.

OFF

OPEN

FIG. 11

TO USE THROTTLE CONTROL (See Fig. 12)

The throttle control is located on the engine. Always operate the snow thrower with the engine at full throttle. Full throttle offers the best snow thrower performance.

FAST

SLOW

FIG. 12

 

TO USE CHOKE CONTROL (See Fig. 13)

 

The choke control is located on the engine. Use the choke

 

control whenever you are starting a cold engine. Do not

 

use to start a warm engine.

10

•To engage choke, turn knob clockwise. Slowly turn knob counterclockwise to disengage.

OFFFULL

FIG. 13

TO CONTROL SNOW DISCHARGE (See Fig. 14)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or au- ger become clogged, shut-off engine and wait for all moving parts to stop. Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

•To change the discharge chute position, press down- ward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther.

•Press downward on chute deflector control lever and move lever forward to lower the deflector and decrease the distance. Move lever back to raise the deflector and increase the distance. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

CHUTE DEFLECTOR

REMOTE CONTROL LEVER

FIG. 14

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 927SBEXP Owners ManualPreparation Safe Operation Practices for Walk-Behind Snow ThrowersTraining OperationMaintenance and Storage TABLE OF CONTENTSPRODUCT SPECIFICATIONS CUSTOMER RESPONSIBILITIESPARTS PACKED SEPARATELY IN CARTON REMOVE SNOW THROWER FROM CARTON ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER INSTALL SPEED CONTROL ROD See Figs. 1 andINSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 and INSTALL AUGER CONTROL ROD See Figs. 5 andINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigCHECK TIRE PRESSURE OPERATION KNOW YOUR SNOW THROWERMEETS A.N.S.I. SAFETY REQUIREMENTS TO USE FUEL SHUT-OFF VALVE See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE THROTTLE CONTROL See FigTO THROW SNOW See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO MOVE FORWARD AND BACKWARD See FigSCRAPER BAR BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig CHECK ENGINE OIL LEVEL See FigBEFORE STOPPING SNOW THROWING TIPSIF RECOIL STARTER HAS FROZEN BEFORE EACH USE MAINTENANCEGENERAL RECOMMENDATIONS LUBRICATIONV-BELTS CLEANINGENGINE AUGER GEAR CASETO ADJUST SNOW THROWER HEIGHT SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key 3. Make sure the augers and all moving parts have completely stoppedTO REPLACE BELTS See Fig TO REMOVE WHEELS See Fig STORAGEOTHER CARBURETORDoes not start TROUBLESHOOTINGLoss of power Engine idles orAUGER HOUSING / IMPELLER ASSEMBLY REPAIR PARTSSNOW THROWER - MODEL NO. 927SBEXP 96193000500, PRODUCT NO. 961 93 532 17 CONTROL PANEL / DISCHARGE CHUTE CONTROL PANEL / DISCHARGE CHUTE HANDLES 15 11HANDLES DRIVE 35 33DRIVE CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 927SBEXP 96193000500, PRODUCT NO. 961 93PART DESCRIPTIONWHEELS / DECALS 1 13532 40 SIEIT ILIB SON PSE RR EMO STUC 5ON ITC ES RANTYWAR TEMENTSTA2002 23-81 ONITA REID SCON YTN ARR AW INTA BO TOE RUD EROC P6 ONITC ES
Top Page Image Contents