Husqvarna 927SBEXP owner manual Repair Parts, Drive

Page 27

REPAIR PARTS

DRIVE

SNOW THROWER - MODEL NO. 927SBEXP (96193000500), PRODUCT NO. 961 93 00-05

KEY

PART

 

NO.

NO.

DESCRIPTION

1

532 14 63-15

Screw, Hex Head 5/16-18 x 3/4

2873 80 05-00 Nut, Lock 5/16-18

3532 15 54-15 Washer, Flat

4

817 49 05-08

Screw, Hex Head 5/16-18 x 1/2

5

532 18 00-17 Bearing, Flange

6

532 18 01-34

Shaft, Auxiliary

7

532 17 92-70

Spacer, Plate

8

532 19 29-07

Plate, Auxiliary

9532 18 00-82 Gear, Intermediate (12/58)

10532 18 00-65 Gear, Pinion

11532 18 77-14 Rod, Clutch

12532 18 00-66 Shaft, Long, Hex

13532 17 88-07 Pin, Pivot

14532 18 40-80 Lever, Shifter / Wheel

15532 17 53-44 Trunnion Bearing Assembly

16532 18 78-57 Bracket, Pivot, Shift

17532 17 98-31 Ring, Rubber Wheel

18532 19 95-09 Plate, Rubber Wheel

19873 93 05-00 Nut, Lock 5/16-18

20532 17 86-13 Hub, Rubber Wheel

21 874 76 05-14 Screw, Hex Head 5/16-18 x 7/8

22532 08 51-79 Retainer, Hairpin

23532 18 01-35 Spring, Bias

24532 18 00-81 Gear, Axle (58 Teeth)

25532 17 86-95 Pin, Pivot Lever

26532 19 77-63 Plate Assembly, Drive

27 532 17 86-21 Shaft, Axle

28532 19 77-64 Shaft, Short Hex

29532 18 40-77 Lever, Shifter Plate

30532 18 40-76 Bracket, Shifter Support

31 872 27 05-05 Bolt, Carriage 5/16-18 x 5/8

32532 18 92-82 Key, Square

33532 18 89-09 Bearing, Flange

34532 18 40-75 Plate, Drive Mounting

35532 18 25-04 Spacer, Bearing

36532 19 10-80 Pulley, Traction Drive

37532 15 53-77 Nut, Lock 5/16-18

38

819 11 15-07

Washer, Flat

39

810 04 05-00

Washer, Lock 5/16

40

874 95 05-12

Screw, Hex Head 5/16-18 x 3/4

41812 00 00-12 Ring, Retaining

42811 05 05-00 Washer, Lock, External Tooth 5/16

43532 17 90-95 Spring, Return

44532 18 42-06 Pin, Roll

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Owners Manual 927SBEXPOperation Safe Operation Practices for Walk-Behind Snow ThrowersTraining PreparationCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS Maintenance and StoragePARTS PACKED SEPARATELY IN CARTON INSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andINSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See Fig INSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 andCHECK TIRE PRESSURE KNOW YOUR SNOW THROWER OPERATIONMEETS A.N.S.I. SAFETY REQUIREMENTS TO USE THROTTLE CONTROL See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE FUEL SHUT-OFF VALVE See FigTO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO THROW SNOW See FigCHECK ENGINE OIL LEVEL See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BARSNOW THROWING TIPS BEFORE STOPPINGIF RECOIL STARTER HAS FROZEN LUBRICATION MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEAUGER GEAR CASE CLEANINGENGINE V-BELTS3. Make sure the augers and all moving parts have completely stopped SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig CARBURETOR STORAGEOTHER TO REMOVE WHEELS See FigEngine idles or TROUBLESHOOTINGLoss of power Does not startREPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLYSNOW THROWER - MODEL NO. 927SBEXP 96193000500, PRODUCT NO. 961 93 532 17 CONTROL PANEL / DISCHARGE CHUTE REPAIR PARTS 15 11 HANDLESREPAIR PARTS 35 33 DRIVEREPAIR PARTS SNOW THROWER - MODEL NO. 927SBEXP 96193000500, PRODUCT NO. 961 93 CHASSIS / ENGINE / PULLEYSDESCRIPTION PART1 13 WHEELS / DECALS532 40 ONITA REID SCON YTN ARR AW INTA BO TOE RUD EROC P6 ONITC ES RANTYWAR TEMENTSTA2002 23-81 SIEIT ILIB SON PSE RR EMO STUC 5ON ITC ES
Top Page Image Contents