Husqvarna 927SBEXP owner manual Repair Parts, Control Panel / Discharge Chute

Page 23

REPAIR PARTS

CONTROL PANEL / DISCHARGE CHUTE

SNOW THROWER - MODEL NO. 927SBEXP (96193000500), PRODUCT NO. 961 93 00-05

KEY	PART
NO.	NO.	DESCRIPTION
1	532 18 33-34	Knob, Lever
2	817 50 10-10	Screw #10-24 x 5/8
3	532 17 86-74 Control Assembly, Deﬂector
4	873 80 06-00	Nut, Lock 3/8-16
5	819 13 13-16	Washer, Flat 3/8
6	532 17 86-59 Control Assembly, Chute Rotater
7	532 18 40-89	Support, Pivot
8	532 15 00-78	Screw, Hex Head 5/16-18 x 3/4

9532 18 45-05 Spring, Deﬂector

10532 17 98-29 Bolt, Shoulder

11532 17 92-46 Washer, Flat 1/4

12873 80 04-00 Nut, Lock 1/4-20

13872 25 05-05 Bolt, Carriage 5/16-18

14873 80 05-00 Nut, Lock 5/16-18

15532 18 41-12 Chute Assembly

16532 18 41-13 Deﬂector Assembly

17532 17 91-45 Seal, Deﬂector

18532 12 84-15 Rivet, Blind

19532 18 33-33 Knob, Speed Control Lever

20 872 27 05-06 Bolt, Carriage 5/16-18 x 3/4

21532 15 54-15 Washer, Flat 5/16

22874 04 10-24 Screw #10-24 x 1-1/2

23532 19 24-49 Control Assembly, Power Steering

25532 15 53-77 Nut, Lock 5/16-18

26532 19 88-75 Lever Assembly, Speed Control

27532 16 96-75 Retainer, Hairpin

28532 18 04-45 Rod, Upper, Speed Control

29532 18 77-16 Rod, Lower, Speed Control

30532 19 27-10 Clamp, Clean-Out Tool

31532 19 21-99 Tool, Clean-Out

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty.

23

Image 23

Contents Owners Manual 927SBEXPOperation Safe Operation Practices for Walk-Behind Snow ThrowersTraining PreparationCUSTOMER RESPONSIBILITIES TABLE OF CONTENTSPRODUCT SPECIFICATIONS Maintenance and StoragePARTS PACKED SEPARATELY IN CARTON INSTALL SPEED CONTROL ROD See Figs. 1 and ASSEMBLY / PRE-OPERATIONHOW TO SET UP YOUR SNOW THROWER REMOVE SNOW THROWER FROM CARTONINSTALL AUGER CONTROL ROD See Figs. 5 and INSTALL TRACTION DRIVE CONTROL ROD See Figs. 3 andCHECK TIRE PRESSURE INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD See FigINSTALL CHUTE DEFLECTOR REMOTE CONTROL See Figs. 8 and KNOW YOUR SNOW THROWER OPERATIONMEETS A.N.S.I. SAFETY REQUIREMENTS TO USE THROTTLE CONTROL See Fig HOW TO USE YOUR SNOW THROWERSTOPPING TO USE FUEL SHUT-OFF VALVE See FigTO MOVE FORWARD AND BACKWARD See Fig USING THE CLEAN-OUT TOOL See FigPOWER STEERING OPERATION See Fig TO THROW SNOW See FigCHECK ENGINE OIL LEVEL See Fig BEFORE STARTING THE ENGINETO ADJUST SKID PLATES See Fig SCRAPER BARIF RECOIL STARTER HAS FROZEN SNOW THROWING TIPSBEFORE STOPPING LUBRICATION MAINTENANCEGENERAL RECOMMENDATIONS BEFORE EACH USEAUGER GEAR CASE CLEANINGENGINE V-BELTS3. Make sure the augers and all moving parts have completely stopped SERVICE AND ADJUSTMENTS1. Be sure throttle is in STOP position 2. Remove safety ignition key TO ADJUST SNOW THROWER HEIGHTTO REPLACE BELTS See Fig CARBURETOR STORAGEOTHER TO REMOVE WHEELS See FigEngine idles or TROUBLESHOOTINGLoss of power Does not startSNOW THROWER - MODEL NO. 927SBEXP 96193000500, PRODUCT NO. 961 93 REPAIR PARTSAUGER HOUSING / IMPELLER ASSEMBLY 532 17 CONTROL PANEL / DISCHARGE CHUTE SNOW THROWER - MODEL NO. 927SBEXP 96193000500, PRODUCT NO. 961 93 15 11 HANDLESSNOW THROWER - MODEL NO. 927SBEXP 96193000500, PRODUCT NO. 961 93 35 33 DRIVESNOW THROWER - MODEL NO. 927SBEXP 96193000500, PRODUCT NO. 961 93 SNOW THROWER - MODEL NO. 927SBEXP 96193000500, PRODUCT NO. 961 93 CHASSIS / ENGINE / PULLEYSDESCRIPTION PART1 13 WHEELS / DECALS532 40 ONITA REID SCON YTN ARR AW INTA BO TOE RUD EROC P6 ONITC ES RANTYWAR TEMENTSTA2002 23-81 SIEIT ILIB SON PSE RR EMO STUC 5ON ITC ES