Husqvarna 924SB-XLS owner manual HOW to USE Your Snow Thrower, Stopping

Page 10

OPERATION

The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear

safety glasses or eye shields while operating your snow thrower or performing any adjust- ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or attempting to start the engine.

STOPPING

TRACTION DRIVE

•Release traction drive control lever to stop the forward or reverse movement of the snow thrower.

AUGER

•Release the auger control lever to stop throwing snow.

ENGINE

1.Move throttle control to “STOP” position.

2.Remove (do not turn) safety ignition key to prevent unauthorized use.

NOTE: Never use choke to stop engine.

TO USE FUEL SHUT-OFF VALVE (See Fig. 11)

The fuel shut-off valve is located beneath the fuel tank on the engine. Always operate the snow thrower with the fuel shut-off valve in the OPEN position.

OFF

OPEN

FIG. 11

TO USE THROTTLE CONTROL (See Fig. 12)

The throttle control is located on the engine. Always operate the snow thrower with the engine at full throttle. Full throttle offers the best snow thrower performance.

FAST

SLOW

FIG. 12

TO USE CHOKE CONTROL (See Fig. 13)

The choke control is located on the engine. Use the choke control whenever you are starting a cold engine. Do not use to start a warm engine.

•To engage choke, turn knob clockwise. Slowly turn knob counterclockwise to disengage.

OFFFULL

FIG. 13

TO CONTROL SNOW DISCHARGE (See Fig. 14)

WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup.

WARNING: If the discharge chute or au- ger become clogged, shut-off engine and wait for all moving parts to stop. Use the clean-out tool, NOT YOUR HANDS, to unclog the chute and/or auger.

The DIRECTION in which snow is to be thrown is controlled by the discharge chute control lever.

•To change the discharge chute position, press downward on discharge chute control lever and move lever left or right until chute is in desired position. Be sure lever springs back and locks into desired position.

The DISTANCE that snow is thrown is controlled by the position of the chute deflector. Set the deflector low to throw snow a short distance; set the deflector higher to throw snow farther.

•Press downward on chute deflector control lever and move lever forward to lower the deflector and decrease the distance. Move lever back to raise the deflector and increase the distance. Be sure lever springs back and locks into desired position.

DISCHARGE CHUTE

CONTROL LEVER

CHUTE DEFLECTOR

REMOTE CONTROL LEVER

FIG. 14

TO THROW SNOW (See Fig. 15)

The auger rotation is controlled by the auger control lever located on the right side handle.

•Squeeze auger control lever to handle to engage the auger and throw snow.

10 • Release the auger control lever to stop throwing snow.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents 924SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower TractionMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationSnow Thrower CleaningEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Assembly 24 LH Auger Assembly 24 RHAuger Ball Bearing Skid PlateWeight BAR CARRIAGEBOLT5/16−18X.750POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles 532 42 17-05 Lower Tube Gray 01.12.002-B 532 17 86-66 Halogen Headlight 532 42 14-48 Headlight Bezel GrayBulb Thrust Washer DriveAxle Shaft Clik PIN92122 2930 01.02.002-C Idler Pulley 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Clevis PINAnti Rotate Bracket Bottom PAN Tecumseh EngineFrame Impeller BeltSteer Cable Bracket LH WheelsSteer Cable Bracket RH Spring CoverWheel Lobe Axle LobeBAG of Parts Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY Retainer PIN532 18 10-35 DECAL, DANGER, Deflector Decals532 18 37-30 DECAL, Remote Deflector Warranty Statement

924SB-XLS specifications

The Husqvarna 924SB-XLS is a robust and highly efficient snow blower designed for homeowners and professionals who need to tackle heavy snowfall with ease. Built with power, durability, and user-friendly features, this machine ensures effective snow removal across various surfaces.

One of the standout features of the Husqvarna 924SB-XLS is its powerful engine, equipped with a reliable 243cc 2-cycle motor. This engine delivers a significant amount of torque, enabling the snow blower to handle even the most stubborn, packed snow. The engine is designed for easy starting, and its high-performance design ensures that the blower can operate efficiently in extremely cold conditions.

The snow blower features a durable and robust auger system, which is capable of clearing a path 24 inches wide and up to 23 inches deep. The heavy-duty auger, combined with its powerful intake, helps efficiently break up and transport the snow through the discharge chute. Additionally, the stainless steel construction of the auger enhances its longevity, making it resistant to wear and tear over time.

An important aspect of the Husqvarna 924SB-XLS is its four-way adjustable discharge chute, which allows users to direct the expelled snow precisely where they want it. This feature is particularly useful for managing snow piles and optimizing clearing efficiency. The chute can be easily adjusted from the operator’s position, ensuring minimal interruption during operation.

The snow blower is equipped with features designed for user comfort and ease of operation. The handlebar is ergonomically designed and height-adjustable, allowing operators of different sizes to work comfortably. Furthermore, the oversized tires provide excellent traction on slippery surfaces, making it easier to maneuver through deep snow.

The Husqvarna 924SB-XLS also includes a built-in electric starter, allowing for hassle-free starting on colder days. With its powerful performance, user-friendly features, and durable construction, the Husqvarna 924SB-XLS is an excellent choice for anyone in need of a high-performance snow blower. Its combination of technology and engineering makes it a reliable tool for efficiently managing winter weather challenges. Whether for residential use or small commercial jobs, this snow blower offers reliability you can count on.
Top Page Image Contents