Husqvarna 924SB-XLS Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before per- forming any service or adjustments:

1.Be sure throttle is in STOP position.

2.Remove safety ignition key.

3.Make sure the augers and all moving

parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 22)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shoulder/shear bolt and hex nut. Should a for- eign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shoulder/shear bolt and spacer. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever

is engaged, check to see if the capscrews have sheared. 16

To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER

1/4-20 x 1-5/8

1/4-20 x 2

HUB

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

 

SPACER

1/4-20

 

 

LOCK-

 

 

NUT

 

 

 

 

AUGER

 

 

HUB

 

 

1/4-20

 

AUGER

LOCKNUT

 

 

 

SHAFT

 

 

IMPELLER

 

 

SHAFT

 

FIG. 22

TO REMOVE BELT COVER (See Fig. 23)

1.Remove two (2) screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

 

BELT

 

COVER

FRAME

SCREWS

FIG. 23

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 924SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonAssembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Discharge Chute / Chute Rotator Head See FigCheck Tire Pressure Operation Know Your Snow ThrowerPrimer TractionMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine Snow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationSnow Thrower CleaningEngine Service and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Assembly 24 LH Auger Assembly 24 RHAuger Ball Bearing Skid PlateWeight BAR CARRIAGEBOLT5/16−18X.750Control Panel / Discharge Chute Knob BlackPOP Rivet 532 42 17-28 Shield Retainer Strap532 42 11-60 LEVER/CABLE Rotator Assembly Gray Cable Assembly GrayRotator Head Rotator Pivot BracketHandles 532 42 17-05 Lower Tube Gray 01.12.002-B 532 17 86-66 Halogen Headlight 532 42 14-48 Headlight Bezel GrayBulb Drive Axle ShaftThrust Washer Clik PIN92122 2930 01.02.002-C 532 18 04-78 Engine Traction Pulley 532 18 77-86 Traction Idler ARMIdler Pulley Clevis PINAnti Rotate Bracket Tecumseh Engine FrameBottom PAN Impeller BeltSteer Cable Bracket LH WheelsSteer Cable Bracket RH Cover Wheel LobeSpring Axle LobePower Cord KEY Part Description 532 03 50-62 Safety Ignition KEYBAG of Parts Retainer PIN532 18 10-35 DECAL, DANGER, Deflector Decals532 18 37-30 DECAL, Remote Deflector Warranty Statement

924SB-XLS specifications

The Husqvarna 924SB-XLS is a robust and highly efficient snow blower designed for homeowners and professionals who need to tackle heavy snowfall with ease. Built with power, durability, and user-friendly features, this machine ensures effective snow removal across various surfaces.

One of the standout features of the Husqvarna 924SB-XLS is its powerful engine, equipped with a reliable 243cc 2-cycle motor. This engine delivers a significant amount of torque, enabling the snow blower to handle even the most stubborn, packed snow. The engine is designed for easy starting, and its high-performance design ensures that the blower can operate efficiently in extremely cold conditions.

The snow blower features a durable and robust auger system, which is capable of clearing a path 24 inches wide and up to 23 inches deep. The heavy-duty auger, combined with its powerful intake, helps efficiently break up and transport the snow through the discharge chute. Additionally, the stainless steel construction of the auger enhances its longevity, making it resistant to wear and tear over time.

An important aspect of the Husqvarna 924SB-XLS is its four-way adjustable discharge chute, which allows users to direct the expelled snow precisely where they want it. This feature is particularly useful for managing snow piles and optimizing clearing efficiency. The chute can be easily adjusted from the operator’s position, ensuring minimal interruption during operation.

The snow blower is equipped with features designed for user comfort and ease of operation. The handlebar is ergonomically designed and height-adjustable, allowing operators of different sizes to work comfortably. Furthermore, the oversized tires provide excellent traction on slippery surfaces, making it easier to maneuver through deep snow.

The Husqvarna 924SB-XLS also includes a built-in electric starter, allowing for hassle-free starting on colder days. With its powerful performance, user-friendly features, and durable construction, the Husqvarna 924SB-XLS is an excellent choice for anyone in need of a high-performance snow blower. Its combination of technology and engineering makes it a reliable tool for efficiently managing winter weather challenges. Whether for residential use or small commercial jobs, this snow blower offers reliability you can count on.
Top Page Image Contents