Husqvarna 924SB-XLS owner manual Storage, Other

Page 18

TO REMOVE WHEELS (See Fig. 25)

•Remove the klik pin and remove wheel from axle.

IMPORTANT: When installing wheel, be sure to use the axle hole closest to the end of the shaft – do not use the hole in the wheel hub (if equipped). Inner hole in axle and hole in wheel hub are not used for your model snow thrower.

KLIK PIN (INSTALL

OUTER HOLE

IN OUTER HOLE

 

OF AXLE ONLY)

 

AXLE

WHEEL

WHEEL HUB

FIG. 25

NOTE: To seal punctures or prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE

See engine manual.

CARBURETOR

Your carburetor is not adjustable. Engine performance should not be affected at altitudes up to 7,000 feet (2,134 meters). If your engine does not operate properly due to suspected carburetor problems, take your snow thrower to a qualified service center.

ENGINE SPEED

Never tamper with the engine governor, which is factory set for proper engine speed. Overspeeding the engine above the factory high speed setting can be dangerous and will void the warranty. If you think the engine-governed high speed needs adjusting, contact a qualified service center, which has proper equipment and experience to make any necessary adjustments.

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in min- imizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ex-

18 haust area is still warm.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 924SB-XLS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Chute Deflector Remote Control Parts Packed Separately in CartonRemove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Traction Drive Control ROD See Figs Install Auger Control ROD See FigsInstall Discharge Chute / Chute Rotator Head See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Primer OperationKnow Your Snow Thrower TractionMeets A.N.S.I. Safety Requirements HOW to USE Your Snow Thrower StoppingTo Adjust Skid Plates See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Move Forward and Backward See FigBefore Starting the Engine Before Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning Snow ThrowerEngine Chute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Assembly 24 LH Auger Assembly 24 RHAuger Ball Bearing Skid PlateWeight BAR CARRIAGEBOLT5/16−18X.750POP Rivet Control Panel / Discharge ChuteKnob Black 532 42 17-28 Shield Retainer StrapRotator Head 532 42 11-60 LEVER/CABLE Rotator Assembly GrayCable Assembly Gray Rotator Pivot BracketHandles 532 42 17-05 Lower Tube Gray 01.12.002-B 532 42 14-48 Headlight Bezel Gray 532 17 86-66 Halogen HeadlightBulb Thrust Washer DriveAxle Shaft Clik PIN92122 2930 01.02.002-C Idler Pulley 532 18 04-78 Engine Traction Pulley532 18 77-86 Traction Idler ARM Clevis PINAnti Rotate Bracket Bottom PAN Tecumseh EngineFrame Impeller BeltWheels Steer Cable Bracket LHSteer Cable Bracket RH Spring CoverWheel Lobe Axle LobeBAG of Parts Power CordKEY Part Description 532 03 50-62 Safety Ignition KEY Retainer PINDecals 532 18 10-35 DECAL, DANGER, Deflector532 18 37-30 DECAL, Remote Deflector Warranty Statement

924SB-XLS specifications

The Husqvarna 924SB-XLS is a robust and highly efficient snow blower designed for homeowners and professionals who need to tackle heavy snowfall with ease. Built with power, durability, and user-friendly features, this machine ensures effective snow removal across various surfaces.

One of the standout features of the Husqvarna 924SB-XLS is its powerful engine, equipped with a reliable 243cc 2-cycle motor. This engine delivers a significant amount of torque, enabling the snow blower to handle even the most stubborn, packed snow. The engine is designed for easy starting, and its high-performance design ensures that the blower can operate efficiently in extremely cold conditions.

The snow blower features a durable and robust auger system, which is capable of clearing a path 24 inches wide and up to 23 inches deep. The heavy-duty auger, combined with its powerful intake, helps efficiently break up and transport the snow through the discharge chute. Additionally, the stainless steel construction of the auger enhances its longevity, making it resistant to wear and tear over time.

An important aspect of the Husqvarna 924SB-XLS is its four-way adjustable discharge chute, which allows users to direct the expelled snow precisely where they want it. This feature is particularly useful for managing snow piles and optimizing clearing efficiency. The chute can be easily adjusted from the operator’s position, ensuring minimal interruption during operation.

The snow blower is equipped with features designed for user comfort and ease of operation. The handlebar is ergonomically designed and height-adjustable, allowing operators of different sizes to work comfortably. Furthermore, the oversized tires provide excellent traction on slippery surfaces, making it easier to maneuver through deep snow.

The Husqvarna 924SB-XLS also includes a built-in electric starter, allowing for hassle-free starting on colder days. With its powerful performance, user-friendly features, and durable construction, the Husqvarna 924SB-XLS is an excellent choice for anyone in need of a high-performance snow blower. Its combination of technology and engineering makes it a reliable tool for efficiently managing winter weather challenges. Whether for residential use or small commercial jobs, this snow blower offers reliability you can count on.
Top Page Image Contents