Husqvarna 96193002300 manual To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 24)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by an authorized service centre/department.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

The belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer. Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUEL TANK - Drain gasoline from fuel tank into a suitable container, out- doors, away from fire or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt and lock washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.Remove traction drive belt from around pulleys.

8.Install new traction drive belt around pulleys and inside belt keeper.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley, separate the snow thrower and repeat step 10. Belt must be fully seated in pulley groove when bringing the snow thrower to- gether.

12.Install the two (2) hex bolts and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install lock washer and bolt and tighten securely (41-47 N-m torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

TRACTION DRIVE BELT

 

ENGINE PULLEY

 

 

LOCKWASHER

 

 

BOLT

 

 

AUGER

 

 

BELT

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

FRAME

AUGER PULLEY

AUGER

HOUSING

 

 

 

BOLTS

FIG. 24

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents SBE OV Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs Install Traction Drive Control ROD See FigsCheck Tire Pressure Install Discharge Chute / Chute Rotator Head See FigInstall Chute Deflector Remote Control See Figs Know Your Snow Thrower OperationPrimer Ignition KEYDischarge chute control lever used to change the di Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR see Fig To USE Drift Cutters See FigTo Start Engine Snow Throwing TipsBefore Stopping If Recoil Starter has FrozenGeneral Recommendations MaintenanceBefore Each USE LubricationEngine CleaningSnow Thrower To Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts KEY Part Description Control Panel / Discharge Chute KEY Part Description Handles Repair Parts Drive 532 41 Chassis / Engine / Pulleys Repair Parts Wheels / Decals 532 41 76-91 Wheel Assembly Warranty Statement

96193002300 specifications

The Husqvarna 96193002300 is a premium lawn mower known for its exceptional performance, durability, and advanced technology, making it an excellent choice for homeowners and professional landscapers alike. This mower combines innovation with user-friendly features, providing a seamless mowing experience.

One of the standout features of the Husqvarna 96193002300 is its powerful engine, which ensures reliable performance across various terrains. The engine is engineered for efficiency, offering strong torque while consuming less fuel. This not only translates to longer mowing times but also reduces the frequency of refueling, making it an economical choice for regular maintenance of your lawn.

The mower boasts a robust cutting deck that enhances its cutting capabilities. The wide deck design allows for a greater cutting swath, enabling faster mowing of larger areas. Additionally, the adjustable cutting height is another significant feature, allowing users to customize their mowing to achieve the desired lawn appearance. This versatility caters to different grass types and conditions, ensuring that the lawn is maintained to perfection.

Equipped with advanced technology, the Husqvarna 96193002300 offers a user-friendly interface that enhances the overall mowing experience. The intuitive controls and ergonomic handles provide comfort during prolonged use. The mower’s self-propelled functionality means that users can navigate across uneven ground with minimal effort, a feature that is particularly beneficial for those with larger properties or challenging landscapes.

Moreover, the Husqvarna 96193002300 incorporates innovative safety features that prioritize user protection. These include safety switches that stop the blade when the user releases the handle and a robust frame construction that minimizes vibrations, ensuring a steady grip and control during operation.

For added convenience, the mower features easy-to-access maintenance points, making it simple to keep the machine in peak condition. Regular maintenance is crucial for longevity, and Husqvarna has designed this model with the user in mind.

In conclusion, the Husqvarna 96193002300 is a top-notch lawn mower that excels in performance, features, and safety. Its combination of power, efficiency, and user-friendly technology makes it a leading choice for anyone serious about lawn care, providing excellent results season after season. Whether you are a homeowner seeking to maintain a pristine lawn or a professional landscaper looking for reliable equipment, this mower stands out as a valuable investment.
Top Page Image Contents