Husqvarna 96193004500 Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 15

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3. Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 18)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a spacer, shear bolt and hex nut. Should a foreign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shear bolt. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever

is engaged, check to see if the capscrews have sheared. 15

To replace the capscrew/shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with spark plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

4.Insert safety ignition key and reconnect spark plug wire to spark plug.

1/4-20

1/4-20 x 1-5/8

1/4-20 x 2

LOCKNUT

CAPSCREW /

SHOULDER /

 

SHEAR BOLT

SHEAR BOLT

 

IMPELLER HUB

 

 

IMPELLER

 

 

SHAFT

 

 

 

AUGER

 

 

HUB

1/4-20

 

 

LOCKNUT

AUGER HUB

AUGER SHAFT

FIG. 18

TO REMOVE BELT COVER (See Fig. 19)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

3.Replace belt cover by installing cover and screws and tighten securely.

BELT

COVER

FRAME

SCREWS

FIG. 19

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Remove Snow Thrower from Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Parts Packed Separately in CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Ignition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsTo USE Choke Control See Fig HOW to USE Your Snow ThrowerStopping To USE Fuel SHUT-OFF Valve See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Check Engine OIL Level See Fig To Adjust Skid Plates See FigBefore Starting the Engine Scraper BAR See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Engine Speed To Adjust Cable Tension See FigTo Remove Wheels See Fig CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Warranty Statement

96193004500, 924SB specifications

The Husqvarna 924SB, model number 96193004500, is a powerful snow blower designed for efficiency and performance in the toughest winter conditions. Adorned with a robust and innovative design, this snow blower is built for homeowners seeking reliable snow-clearing solutions for driveways, sidewalks, and other areas prone to heavy snowfall.

One of the key features of the Husqvarna 924SB is its powerful engine, equipped with a 24-inch clearing width and a 23-inch intake height. This allows for the removal of snow quickly and effectively, making it suitable for moderate to heavy snowfall. The engine boasts a reliable starting system, ensuring that the snow blower is ready to go even in frigid temperatures.

The 924SB employs a two-stage snow throwing system, which allows for efficient snow removal by utilizing an auger to gather snow before throwing it out through a chute. This system enhances its capability to tackle compacted and heavy snow, ensuring that users can maintain clean pathways with ease.

Another remarkable aspect of the Husqvarna 924SB is its adjustable chute, allowing users to direct the thrown snow precisely where it is needed, reducing the chances of creating hazards or blocking pathways. The auger height can also be adjusted to accommodate varying snow conditions, providing versatile performance whether dealing with light powder snow or heavy, wet snowfall.

The snow blower features a reliable, user-friendly control panel that allows for easy operation. The ergonomic handle provides comfort during extended use, with heated grips being a notable addition that enhances user comfort during cold winter days. The machine is also designed with durability in mind, featuring a solid, rugged construction to withstand the demanding tasks of snow removal.

With its impressive features, the Husqvarna 924SB delivers exceptional performance, making it an invaluable tool for homeowners facing harsh winter weather. Its combination of power, advanced technology, ease of use, and reliability positions it as a top choice in the snow blower market, ensuring users can enjoy a safe, clear, and accessible outdoor space during winter months. Whether facing light flurries or severe storms, the Husqvarna 924SB proves to be a steadfast companion against winter's challenges.
Top Page Image Contents