Husqvarna 924SB, 96193004500 manual Storage, Other, Fuel System, Engine OIL, Cylinder

Page 18

STORAGE

Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more.

WARNING: Never store the snow thrower with gasoline in the tank inside a building where fumes may reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or gas appliance. Allow the engine to cool before storing in any enclosure.

SNOW THROWER

When snow thrower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

1.Clean entire snow thrower (See “CLEANING” in the Maintenance section of this manual).

2.Inspect and replace belts, if necessary (See “TO RE- PLACE BELTS” in the Service and Adjustments section of this manual).

3.Lubricate as shown in the Maintenance section of this manual.

4.Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

5.Touch up all rusted or chipped paint surfaces; sand lightly before painting.

ENGINE

See engine manual.

FUEL SYSTEM

IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, fuel hose, or tank during storage. Also, alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage.

•Empty the fuel tank by starting the engine and letting it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean engine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER

1.Remove spark plug.

2.Pour one ounce (29 ml) of oil through spark plug hole into cylinder.

3.Pull recoil starter handle slowly a few times to distribute oil.

4.Replace with new spark plug.

OTHER

•Remove safety ignition key; store it in a safe place.

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your snow thrower indoors and cover it to protect it from dust and dirt.

•Cover your snow thrower with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe, which allows condensation to form and will cause your snow thrower to rust.

IMPORTANT: Never cover snow thrower while engine/ exhaust area is still warm.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents 924SB Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonInstall Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigCheck Tire Pressure Primer OperationKnow Your Snow Thrower Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineTo USE Fuel SHUT-OFF Valve See Fig HOW to USE Your Snow ThrowerStopping To USE Choke Control See FigUsing the CLEAN-OUT Tool See Fig To Throw Snow See FigTo Move Forward and Backward See Fig Scraper BAR See Fig To Adjust Skid Plates See FigBefore Starting the Engine Check Engine OIL Level See FigBefore Stopping Snow Throwing TipsTo Start Engine If Recoil Starter has FrozenBefore Each USE MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Service and AdjustmentsTo Adjust Snow Thrower Height Shear Bolts See FigTo Replace Belts See Fig Carburetor To Adjust Cable Tension See FigTo Remove Wheels See Fig Engine SpeedFuel System StorageOther Engine OILTroubleshooting Warranty Statement

96193004500, 924SB specifications

The Husqvarna 924SB, model number 96193004500, is a powerful snow blower designed for efficiency and performance in the toughest winter conditions. Adorned with a robust and innovative design, this snow blower is built for homeowners seeking reliable snow-clearing solutions for driveways, sidewalks, and other areas prone to heavy snowfall.

One of the key features of the Husqvarna 924SB is its powerful engine, equipped with a 24-inch clearing width and a 23-inch intake height. This allows for the removal of snow quickly and effectively, making it suitable for moderate to heavy snowfall. The engine boasts a reliable starting system, ensuring that the snow blower is ready to go even in frigid temperatures.

The 924SB employs a two-stage snow throwing system, which allows for efficient snow removal by utilizing an auger to gather snow before throwing it out through a chute. This system enhances its capability to tackle compacted and heavy snow, ensuring that users can maintain clean pathways with ease.

Another remarkable aspect of the Husqvarna 924SB is its adjustable chute, allowing users to direct the thrown snow precisely where it is needed, reducing the chances of creating hazards or blocking pathways. The auger height can also be adjusted to accommodate varying snow conditions, providing versatile performance whether dealing with light powder snow or heavy, wet snowfall.

The snow blower features a reliable, user-friendly control panel that allows for easy operation. The ergonomic handle provides comfort during extended use, with heated grips being a notable addition that enhances user comfort during cold winter days. The machine is also designed with durability in mind, featuring a solid, rugged construction to withstand the demanding tasks of snow removal.

With its impressive features, the Husqvarna 924SB delivers exceptional performance, making it an invaluable tool for homeowners facing harsh winter weather. Its combination of power, advanced technology, ease of use, and reliability positions it as a top choice in the snow blower market, ensuring users can enjoy a safe, clear, and accessible outdoor space during winter months. Whether facing light flurries or severe storms, the Husqvarna 924SB proves to be a steadfast companion against winter's challenges.
Top Page Image Contents