Husqvarna 9027STE owner manual To Replace Belts See Fig

Page 17

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 24)

The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear, they should be replaced. It is recommended that the belt(s) be replaced by a qualified service center.

NOTE: It is recommended that both the auger and traction drive belt be replaced at the same time.

TheV-belts on your snow thrower are of special construction and should be replaced by original equipment manufacturer (OEM) belts available from your nearest dealer.Using other than OEM belts can cause personal injury or damage to the snow thrower.

WARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly, it is important that an assistant stand in the operating position and hold the snow thrower handles. Se- rious personal injury and/or damage to the unit could occur if the snow thrower should fall during the belt changing process.

FRAME

AUGER

ASSEMBLY

HOUSING

HANDLES

1.REMOVE GASOLINE FROM FUELTANK - Drain gaso- line from fuel tank into a suitable container, outdoors, away from fi re or flame. Wipe up any spilled gasoline.

2.REMOVE DISCHARGE CHUTE - Loosen locknut securing chute rotator head to mounting bracket only enough to allow chute rotator head to be raised and discharge chute to be removed from snow thrower.

3.REMOVE BELT COVER - See “TO REMOVE BELT COVER” in this section of this manual.

4.REMOVE ENGINE PULLEY - Remove bolt, lockwasher and fl at washer securing pulley to engine crankshaft. Remove outside (auger) pulley only from crankshaft.

5.SEPARATE SNOW THROWER - With your assistant standing in the operating position holding the handles, remove the two (2) bolts and lock washers holding auger housing and frame together.

WARNING: As the last bolt is removed, have your assistant carefully lower the handles down to the ground.

6.REMOVE AUGER BELT from around pulley.

7.RELIEVE TENSION ON TRACTION DRIVE BELT IDLER and remove traction drive belt from around pulleys.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension.

8.With tension relieved on idler, install new traction drive belt around pulleys and inside belt keepers.

9.Place auger belt around and inside the groove of auger pulley only.

10.While your assistant slowly raises handles to rejoin the auger housing and frame assembly, pull up on the auger belt and squeeze sides together above pulley so belt is fully seated in groove of pulley.

11.Bring snow thrower completely together and check carefully for proper routing of belts. If auger belt has become dislodged from the pulley (by catching the idler arm bracket while bringing snow thrower together), separate the snow thrower and repeat step 10. Belt must be fully seated in pulley groove when bringing the snow thrower together.

12.Install the two (2) hex bolts and lock washers and tighten securely.

13.INSTALL ENGINE PULLEY - Place belt in pulley groove and slide pulley on crankshaft. Install fl at washer, lock- washer and bolt and tighten securely (30-35 ft. lbs. torque). Make sure belt is inside belt keeper.

14.INSTALL BELT COVER and two (2) screws. Tighten securely.

15.INSTALL DISCHARGE CHUTE – See “INSTALL DIS- CHARGE CHUTE / CHUTE ROTATER HEAD” in the Assembly / Pre-Operation section of this manual.

 

BELT KEEPER

 

 

 

TRACTION DRIVE BELT

 

 

ENGINE

FLAT WASHER

 

PULLEY

 

 

 

 

 

LOCKWASHER

 

 

BOLT

IDLER ARM

 

 

AUGER

SQUARE

 

 

BELT

HOLE

 

 

 

CLUTCHING

 

 

IDLER ARM

 

 

BRACKET

 

 

 

AUGER PULLEY

 

 

 

 

BOLT

LOCK

 

 

 

WASHER

FRAME

AUGER

 

 

 

HOUSING

 

 

17

FIG. 24

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 9027STE XP Preparation TrainingOperation Static Electricity HazardAPI SG-SL Maintenance and StorageParts Packed Separately in Carton Service and Adjustments14-15 16-18HOW to SET UP Your Snow Thrower Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleInstall Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsInstall Weight BAR See Fig Know Your Snow Thrower OperationRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerPower Steering Operation See Fig Using the CLEAN-OUT Tool See FigTo Throw Snow See Fig To Move Forward and Backward See FigTo Start Engine Before Starting the EngineScraper BAR If Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations MaintenanceBefore Each USE LubricationEngine CleaningTo Adjust Snow Thrower Height Service and AdjustmentsChute Deflector Shear Bolts See FigTo Replace Belts See Fig Other StorageTroubleshooting Repair Parts Auger Housing / Impeller Assembly KEY Part Description Repair Parts Repair Parts Repair Parts Handles Handles Drive Repair Parts Chassis / Engine / Pullys KEY Part Description Repair Parts Wheels / Decals Wheels / Decals Sion Tmita ILD NA SON ITP Eexc 4ON ITC ES Rantywar Tementsta

9027STE specifications

The Husqvarna 9027STE is a powerful and versatile lawn mower designed specifically for tackling challenging terrains and delivering a superior cutting experience. Built with robust features and advanced technologies, this machine stands out in the competitive market of outdoor power equipment.

One of the key attributes of the 9027STE is its efficient cutting system. It boasts a wide cutting deck that allows for faster mowing, reducing the time spent on lawn care. The cutting height is conveniently adjustable, enabling users to customize the grass length to their preference. With its durable blades, the mower provides a clean, sharp cut, promoting healthy grass growth and an aesthetically pleasing lawn.

Powered by a reliable engine, the Husqvarna 9027STE offers exceptional performance and longevity. Its efficient engine design ensures low fuel consumption while still delivering ample power for tackling tough grass and uneven terrain. This enhances the mower’s capability to operate over large areas without frequent refueling, making it ideal for large properties or commercial use.

Incorporating advanced technology, the 9027STE features ergonomic controls that improve user comfort and ease of operation. The intuitive control layout allows for effortless maneuvering, reducing operator fatigue during prolonged use. The lawn mower's compact design further enhances its maneuverability, enabling users to navigate around obstacles and tight spaces with ease.

Safety is a priority with the Husqvarna 9027STE, which is equipped with various safety features including an automatic shut-off mechanism that engages when the mower is not in use, preventing accidental starts. This adds an extra layer of protection for the operator, especially when working in proximity to children or pets.

Another standout characteristic of the 9027STE is its durability. Made from high-quality materials, the mower is built to withstand the rigors of regular use and is resistant to wear and tear, ensuring a long lifespan. Moreover, the model is easy to maintain, with readily accessible components making it simple for users to service and keep in optimal condition.

Overall, the Husqvarna 9027STE is a top-tier choice for those seeking a reliable, efficient, and user-friendly lawn mower. Its combination of power, advanced features, and durability makes it an investment worth considering for both residential and commercial lawn care needs. Whether you're a homeowner maintaining a lush garden or a professional landscaper, the 9027STE promises to deliver impressive results and convenience.
Top Page Image Contents