Husqvarna 10527SB-LS Service and Adjustments, To Adjust Snow Thrower Height, Chute Deflector

Page 16

SERVICE AND ADJUSTMENTS

WARNING: To avoid serious injury, before performing any service or adjustments:

1.Be sure the on/off switch is in the OFF position.

2.Remove safety ignition key.

3.Make sure the augers and all moving parts have completely stopped.

4.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

3.Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely.

CAUTION: Do not substitute. Use only original equipment capscrew/shear bolts as supplied with your snow thrower.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

See “TO ADJUST SKID PLATES” and “SCRAPER BAR” in the Operation section of this manual.

CHUTE DEFLECTOR

The chute deflector, attached to the top of the discharge chute, is provided to direct discharging snow away from the operator. If the deflector becomes damaged, it should be replaced.

WARNING: To avoid serious injury, never operate your snow thrower with the deflector removed or damaged.

•To change direction and/or distance snow is discharged, see “TO CONTROL SNOW DISCHARGE” in the Op- eration section of this manual.

SHEAR BOLTS (See Fig. 21)

AUGER SHEAR BOLTS

Both right and left-hand augers are secured to the auger shaft with a shoulder/shear bolt and hex nut. Should a for- eign object or ice become lodged in the augers, the shear bolts are designed to break, preventing damage to any other components. If one or both augers do not turn when auger control lever is engaged, check to see if one or both of the bolts have sheared. To replace the shear bolts:

1.Disengage all controls and move throttle control to STOP position. Wait for all moving parts to stop.

2.Remove safety ignition key and disconnect spark plug wire from spark plug. Place wire where it cannot come in contact with plug.

3.Align hole in auger hub with hole in auger shaft and install a new 1/4-20 x 2" shoulder/shear bolt and spacer. Install 1/4-20 lock nut and tighten securely.

CAUTION: Do not substitute. Use only original equipment shear bolts as supplied with your snow thrower.

4.Connect spark plug wire to spark plug. Replace safety ignition key

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2) capscrew/shear bolts and hex nuts. Should a foreign object or ice become lodged in the impeller, the capscrews are designed to break, preventing damage to any other com- ponents. If impeller does not turn when auger control lever is engaged, check to see if the capscrews have sheared. To replace the capscrew/shear bolts:

16

4. Connect spark plug wire to spark plug.

1/4-20 x 1-5/8

1/4-20 x 2

CAPSCREW /

SHOULDER /

SHEAR BOLT

SHEAR BOLT

IMPELLER

 

HUB

 

1/4-20

 

LOCKNUT

 

 

SPACER

 

AUGER HUB

 

1/4-20 LOCKNUT

 

AUGER

 

SHAFT

 

IMPELLER

 

SHAFT

FIG. 21

TO REMOVE BELT COVER (See Fig. 22)

1.Remove the two (2) screws securing belt cover to frame.

2.Remove belt cover.

•Replace belt cover by installing cover and screws and tighten securely.

 

BELT

 

COVER

FRAME

SCREWS

FIG. 22

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 10527SB-LS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Auger Control ROD See Figs Install Discharge Chute / Chute Rotater Head See FigInstall Chute Deflector Remote Control See Figs Check Tire PressureOperation Know Your Snow ThrowerPrimer Ignition KEYMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the engineHOW to USE Your Snow Thrower StoppingUsing the CLEAN-OUT Tool See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigBefore Starting the Engine Scraper BARTo USE Drift Cutters See Fig Check Engine OIL Level See FigSnow Throwing Tips To Start EngineBefore Stopping If Recoil Starter has FrozenMaintenance General RecommendationsBefore Each USE LubricationCleaning EngineService and Adjustments To Adjust Snow Thrower HeightChute Deflector Shear Bolts See FigTo Replace Belts See Fig Storage OtherTroubleshooting Repair Parts Auger Housing / Impeller AssemblyKEY Part Description Auger Ball Bearing Auger Assembly 27 RH Auger Assembly 27 LHSkid Plate CARRIAGEBOLT5/16−18X.750 Control Panel / Discharge Chute Knob BlackPOP Rivet 532 42 17-28 Shield Retainer Strap532 42 11-61 Rotator Pivot Bracket LEVER/CABLE Rotator Assembly GraySteer Cable Handles POP Rivet 1/8532 42 16-13 Spacer Control Lever RetainerKnob RED Handle KnobRear Plate Clutch ROD13 532 41 54-33 Shifter Plate Bracket Grip Switch Wire Harness532 42 14-48 Headlight Bezel Gray BulbDrive 14 15 FSheet2 Speed Selector Head Assembly Drive Plate WeldmentPIN 16 175338 Drive Mount PlateAxle Shaft Roll PIN 3/16Gear Clik PINChassis / Engine / Pulleys Repair Parts CoverWheel Lobe Axle LobeSteer Cable Bracket LH WheelsSteer Cable Bracket RH Power Cord KEY Part Description 532 19 30-71 Safety Ignition KEYBAG of Parts Retainer PIN532 18 10-35 DECAL, DANGER, Deflector 10 532 18 37-30 DECAL, Remote DeflectorWarranty Statement

10527SB-LS specifications

The Husqvarna 10527SB-LS is a powerful snow blower designed to tackle heavy snow accumulation with ease, making it a reliable choice for homeowners and professionals alike. This model is particularly noted for its impressive performance in harsh winter conditions, combining innovative technologies and user-friendly features to deliver efficiency and reliability.

One of the standout features of the Husqvarna 10527SB-LS is its robust 27-inch clearing width, making it capable of handling large areas quickly. The machine is powered by a strong, reliable engine that provides ample power to navigate through heavy, wet snow, ensuring that even the toughest winter storms are no match for its performance.

Equipped with a two-stage snow removal system, the 10527SB-LS excels in its ability to throw snow far from the path, thanks to its high-speed impeller. This two-stage process consists of an auger that gathers snow and ice, which is then discharged through a chute, effectively clearing driveways, sidewalks, and other surfaces. The adjustable chute enables users to direct the snow exactly where it is needed, enhancing the efficiency of the snow clearing process.

The snow blower’s heavy-duty construction is built to withstand the rigors of winter use. Its durable metal frame and components are designed to last, ensuring that the 10527SB-LS can tackle multiple seasons without significant wear. Additionally, the large, rugged tires provide excellent traction, enabling the machine to maneuver through snow and challenging terrains easily.

Comfort and usability are also key selling points for the Husqvarna 10527SB-LS. It features an ergonomic handle with controls easily accessible, allowing for smooth operations without straining the operator. The electric start function adds further convenience, allowing the operator to start the engine quickly with the push of a button rather than relying on a pull-cord system.

Safety is prioritized in the design of the 10527SB-LS, with features like an automatic safety shut-off in case of unexpected situations. This ensures that users can operate the snow blower with confidence.

Overall, the Husqvarna 10527SB-LS is a comprehensive snow removal solution that combines power, durability, and ease of use. Its range of features makes it well-equipped to handle the requirements of winter weather, making it an excellent investment for anyone looking to simplify their snow clearing tasks. Whether for a residential driveway or larger outdoor spaces, this snow blower stands out as an efficient and reliable tool.
Top Page Image Contents