Husqvarna 10527SB-LS owner manual Table of Contents

Page 3

6.When cleaning, repairing or inspecting the snow thrower, stop the engine and make certain the collector/impel- ler and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the engine.

7.Do not run the engine indoors, except when starting the engine and for transporting the snow thrower in or out of the building. Open the outside doors; exhaust fumes are dangerous.

8.Exercise extreme caution when operating on slopes.

9.Never operate the snow thrower without proper guards, and other safety protective devices in place and work- ing.

10.Never direct the discharge toward people or areas where property damage can occur. Keep children and others away.

11.Do not overload the machine capacity by attempting to clear snow at too fast a rate.

12.Never operate the machine at high transport speeds on slippery surfaces. Look behind and use care when operating in reverse.

13.Disengage power to the collector/impeller when snow thrower is transported or not in use.

14.Use only attachments and accessories approved by the manufacturer of the snow thrower (such as wheel weights, counterweights, or cabs).

15.Never operate the snow thrower without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk; never run.

16.Never touch a hot engine or muffler.

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge chute is the most common cause of injury associated with snow throwers. Never use your hand to clean out the dis- charge chute. To clear the chute:

1.SHUT THE ENGINE OFF!

2.Wait 10 seconds to be sure the impeller blades have stopped rotating.

3.Always use a clean-out tool, not your hands.

Maintenance and Storage

1.Check shear bolts and other bolts at frequent intervals for proper tightness to be sure the equipment is in safe working condition.

2.Never store the machine with fuel in the fuel tank inside a building where ignition sources are present such as hot water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure.

3.Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period.

4.Maintain or replace safety and instruction labels, as necessary.

5.Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller.

CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and manufac- tured to give best possible dependability and performance.

Should you experience any problem you cannot easily remedy, please contact your nearest authorized service center. We have competent, well-trained technicians and the proper tools to service or repair this unit.

Please read and retain this manual. The instructions will enable you to assemble and maintain your snow thrower properly. Always observe the “SAFETY RULES”.

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THE MODEL AND SERIAL NUMBERS WILL BE FOUND ON A DECAL ATTACHED TO THE REAR OF THE SNOW THROWER HOUSING.

YOU SHOULD RECORD BOTH SERIAL NUMBER AND DATE OF PURCHASE AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

PRODUCT SPECIFICATIONS

Gasoline Capacity

3.0 Quarts (2,84 Liters)

and Type:

Unleaded Regular only

 

 

Oil Type

SAE 5W-30 or 10W-30

(API SG–SL):

Synthetic SAE 5W-30

 

 

Oil Capacity:

28 Ounces (0,83 Liters)

 

 

Spark Plug:

Champion QC12YC

Gap:

0.030" (0,762 mm)

 

 

CUSTOMER RESPONSIBILITIES

•Read and observe the safety rules.

•Follow a regular schedule in maintaining, caring for and using your snow thrower.

•Follow the instructions under “Maintenance” and “Stor- age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES

2-3

PRODUCT SPECIFICATIONS

3

CUSTOMER RESPONSIBILITIES

3

ASSEMBLY / PRE-OPERATION

4-7

OPERATION

8-13

MAINTENANCE SCHEDULE

14

MAINTENANCE

14-15

SERVICE AND ADJUSTMENTS

16-18

STORAGE

18

TROUBLESHOOTING

19

REPAIR PARTS

20-39

3 WARRANTY

BACK PAGE

Page 2 Page 4
Image 3
Page 2 Page 4
Contents 10527SB-LS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents Parts Packed Separately in Carton Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Install Speed Control ROD See Figs Install Traction Drive Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Ball Bearing Auger Assembly 27 LH Auger Assembly 27 RHSkid Plate CARRIAGEBOLT5/16−18X.750 532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP RivetLEVER/CABLE Rotator Assembly Gray 532 42 11-61 Rotator Pivot BracketSteer Cable POP Rivet 1/8 HandlesHandle Knob 532 42 16-13 Spacer Control LeverRetainer Knob REDClutch ROD Rear Plate13 532 41 54-33 Shifter Plate Bracket Bulb Grip SwitchWire Harness 532 42 14-48 Headlight Bezel GrayDrive 14 15 FSheet2 16 175338 Drive Mount Plate Speed Selector Head AssemblyDrive Plate Weldment PINClik PIN Axle ShaftRoll PIN 3/16 GearChassis / Engine / Pulleys Axle Lobe Repair PartsCover Wheel LobeWheels Steer Cable Bracket LHSteer Cable Bracket RH Retainer PIN Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY BAG of Parts10 532 18 37-30 DECAL, Remote Deflector 532 18 10-35 DECAL, DANGER, DeflectorWarranty Statement

10527SB-LS specifications

The Husqvarna 10527SB-LS is a powerful snow blower designed to tackle heavy snow accumulation with ease, making it a reliable choice for homeowners and professionals alike. This model is particularly noted for its impressive performance in harsh winter conditions, combining innovative technologies and user-friendly features to deliver efficiency and reliability.

One of the standout features of the Husqvarna 10527SB-LS is its robust 27-inch clearing width, making it capable of handling large areas quickly. The machine is powered by a strong, reliable engine that provides ample power to navigate through heavy, wet snow, ensuring that even the toughest winter storms are no match for its performance.

Equipped with a two-stage snow removal system, the 10527SB-LS excels in its ability to throw snow far from the path, thanks to its high-speed impeller. This two-stage process consists of an auger that gathers snow and ice, which is then discharged through a chute, effectively clearing driveways, sidewalks, and other surfaces. The adjustable chute enables users to direct the snow exactly where it is needed, enhancing the efficiency of the snow clearing process.

The snow blower’s heavy-duty construction is built to withstand the rigors of winter use. Its durable metal frame and components are designed to last, ensuring that the 10527SB-LS can tackle multiple seasons without significant wear. Additionally, the large, rugged tires provide excellent traction, enabling the machine to maneuver through snow and challenging terrains easily.

Comfort and usability are also key selling points for the Husqvarna 10527SB-LS. It features an ergonomic handle with controls easily accessible, allowing for smooth operations without straining the operator. The electric start function adds further convenience, allowing the operator to start the engine quickly with the push of a button rather than relying on a pull-cord system.

Safety is prioritized in the design of the 10527SB-LS, with features like an automatic safety shut-off in case of unexpected situations. This ensures that users can operate the snow blower with confidence.

Overall, the Husqvarna 10527SB-LS is a comprehensive snow removal solution that combines power, durability, and ease of use. Its range of features makes it well-equipped to handle the requirements of winter weather, making it an excellent investment for anyone looking to simplify their snow clearing tasks. Whether for a residential driveway or larger outdoor spaces, this snow blower stands out as an efficient and reliable tool.
Top Page Image Contents