Husqvarna 10527SB-LS owner manual Troubleshooting

Page 19

TROUBLESHOOTING

See appropriate section in manual unless directed to a qualified service centre.

PROBLEM

 

CAUSE

 

CORRECTION

Does not start

1.

Fuel shut-off valve (if so

1.

Turn fuel shut-off valve to OPEN position.

 

 

equipped) in OFF position.

 

 

 

2.

Safety ignition key

2.

Insert safety ignition key.

 

 

is not inserted.

 

 

 

3.

Out of fuel.

3.

Refill fuel tank with fresh, clean gasoline.

 

4.

Throttle in STOP position.

4.

Move throttle to FAST position.

 

5.

Choke in OFF position.

5.

Move to FULL position.

 

6.

Primer not depressed.

6.

Prime as instructed in the Operation section of this manual.

 

7.

Engine is flooded.

7.

Wait a few minutes before restarting, DO NOT prime.

 

8.

Spark plug wire is

8.

Connect wire to spark plug.

 

 

disconnected.

 

 

 

9.

Bad spark plug.

9.

Replace spark plug.

 

10.

Stale fuel.

10.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

11.

Water in fuel.

11.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

 

 

 

 

Loss of power

1.

Spark plug wire loose.

1.

Reconnect spark plug wire.

 

2.

Throwing too much snow.

2.

Reduce speed and width of swath.

 

3.

Fuel tank cap is covered

3.

Remove ice and snow on and around fuel tank cap.

 

 

with ice or snow.

 

 

 

4.

Dirty or clogged muffler.

4.

Clean or replace muffler.

 

 

 

 

 

Engine idles or

1.

Choke is in FULL position.

1.

Move choke to OFF position.

runs roughly

2.

Blockage in fuel line.

2.

Clean fuel line.

 

3.

Stale fuel.

3.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

4.

Water in fuel.

4.

Empty fuel tank & carburetor, refill with fresh, clean gasoline.

 

5.

Carburetor is in need of

5.

Contact a qualified service centre.

 

 

adjustment or overhaul.

 

 

 

 

 

 

 

Excessive

1.

Loose parts or damaged

1.

Tighten all fasteners. Replace damaged parts.

vibration

 

augers or impeller.

 

If vibration remains, contact a qualified service centre.

 

 

 

 

 

Recoil starter

1.

Frozen recoil starter.

1.

See “IF RECOIL STARTER HAS FROZEN”

is hard to pull

 

 

 

in the Operation section of this manual.

 

 

 

 

 

Loss of traction

1.

Drive belt is worn.

1.

Check / replace drive belt.

drive / slowing

2.

Drive belt is off of pulley.

2.

Check / reinstall drive belt.

of drive speed

3.

Friction drive wheel is worn.

3.

Contact a qualified service centre.

 

 

 

 

 

Loss of snow

1.

Auger belt is off of pulley.

1.

Check / reinstall auger belt.

discharge or

2.

Auger belt is worn.

2.

Check / replace auger belt.

slowing of

3.

Clogged discharge chute.

3.

Clean snow chute.

snow discharge

4.

Augers / impeller jammed.

4.

Remove debris or foreign object from augers / impeller.

 

 

 

 

 

19

Image 19
Contents 10527SB-LS Safe Operation Practices for Walk-Behind Snow Throwers Table of Contents HOW to SET UP Your Snow Thrower Parts Packed Separately in Carton Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Install Traction Drive Control ROD See Figs Install Speed Control ROD See FigsUnfold Upper Handle Install Discharge Chute / Chute Rotater Head See Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsIgnition KEY OperationKnow Your Snow Thrower PrimerRecoil auxiliary starter handle used for starting the engine Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Using the CLEAN-OUT Tool See FigPower Steering Operation See Fig To Adjust Skid Plates See FigCheck Engine OIL Level See Fig Before Starting the EngineScraper BAR To USE Drift Cutters See FigIf Recoil Starter has Frozen Snow Throwing TipsTo Start Engine Before StoppingLubrication MaintenanceGeneral Recommendations Before Each USEEngine CleaningShear Bolts See Fig Service and AdjustmentsTo Adjust Snow Thrower Height Chute DeflectorTo Replace Belts See Fig Other StorageTroubleshooting Auger Housing / Impeller Assembly Repair PartsKEY Part Description Auger Ball Bearing Auger Assembly 27 RH Auger Assembly 27 LHSkid Plate CARRIAGEBOLT5/16−18X.750 532 42 17-28 Shield Retainer Strap Control Panel / Discharge ChuteKnob Black POP Rivet532 42 11-61 Rotator Pivot Bracket LEVER/CABLE Rotator Assembly GraySteer Cable POP Rivet 1/8 HandlesHandle Knob 532 42 16-13 Spacer Control LeverRetainer Knob REDRear Plate Clutch ROD13 532 41 54-33 Shifter Plate Bracket Bulb Grip SwitchWire Harness 532 42 14-48 Headlight Bezel GrayDrive 14 15 FSheet2 16 175338 Drive Mount Plate Speed Selector Head AssemblyDrive Plate Weldment PINClik PIN Axle ShaftRoll PIN 3/16 GearChassis / Engine / Pulleys Axle Lobe Repair PartsCover Wheel LobeSteer Cable Bracket LH WheelsSteer Cable Bracket RH Retainer PIN Power CordKEY Part Description 532 19 30-71 Safety Ignition KEY BAG of Parts10 532 18 37-30 DECAL, Remote Deflector 532 18 10-35 DECAL, DANGER, DeflectorWarranty Statement

10527SB-LS specifications

The Husqvarna 10527SB-LS is a powerful snow blower designed to tackle heavy snow accumulation with ease, making it a reliable choice for homeowners and professionals alike. This model is particularly noted for its impressive performance in harsh winter conditions, combining innovative technologies and user-friendly features to deliver efficiency and reliability.

One of the standout features of the Husqvarna 10527SB-LS is its robust 27-inch clearing width, making it capable of handling large areas quickly. The machine is powered by a strong, reliable engine that provides ample power to navigate through heavy, wet snow, ensuring that even the toughest winter storms are no match for its performance.

Equipped with a two-stage snow removal system, the 10527SB-LS excels in its ability to throw snow far from the path, thanks to its high-speed impeller. This two-stage process consists of an auger that gathers snow and ice, which is then discharged through a chute, effectively clearing driveways, sidewalks, and other surfaces. The adjustable chute enables users to direct the snow exactly where it is needed, enhancing the efficiency of the snow clearing process.

The snow blower’s heavy-duty construction is built to withstand the rigors of winter use. Its durable metal frame and components are designed to last, ensuring that the 10527SB-LS can tackle multiple seasons without significant wear. Additionally, the large, rugged tires provide excellent traction, enabling the machine to maneuver through snow and challenging terrains easily.

Comfort and usability are also key selling points for the Husqvarna 10527SB-LS. It features an ergonomic handle with controls easily accessible, allowing for smooth operations without straining the operator. The electric start function adds further convenience, allowing the operator to start the engine quickly with the push of a button rather than relying on a pull-cord system.

Safety is prioritized in the design of the 10527SB-LS, with features like an automatic safety shut-off in case of unexpected situations. This ensures that users can operate the snow blower with confidence.

Overall, the Husqvarna 10527SB-LS is a comprehensive snow removal solution that combines power, durability, and ease of use. Its range of features makes it well-equipped to handle the requirements of winter weather, making it an excellent investment for anyone looking to simplify their snow clearing tasks. Whether for a residential driveway or larger outdoor spaces, this snow blower stands out as an efficient and reliable tool.