All Installations

1.Strip 1/2-inch (13mm) of insula- tion from the wire, and twist the wire strands together. The HSi speaker jack will accept either bare wire up to 12- gauge, or single banana plugs.

2.Connect the wire to the speaker.

3.Slide the speaker into the cutout as shown.The speaker must slide into the wall woofer side first.

4.Tighten the Phillips mounting screws.

Important: Do not over tight- en the screws.

If you wish to paint your speakers or grilles it should be done prior to installation of the grille. Please see the Painting instructions.

5.If the speaker has been mount- ed in a horizontal position, remove the tie tack logo and reinstall along the long axis of the grille.

6.Insert the grille into the slots in the baffle by gently applying pressure along the edge.

Todas las instalaciones

1.Pele 13mm del aislante del cable y retuerza el extremo para agrupar los hilos. El conector del altavoz HSi aceptará tanto cable desnudo de calibre 12 como con clavijas sencillas tipo banana.

2.Conecte el cable al altavoz.

3.Introduzca el altavoz en el agu- jero como se indica. Deben introducirse primero en la pared del “lado del woofer”.

4.Apriete los tornillos tipo estrel- la de montaje.

Importante: no apriete demasiado los tornillos.

Si quiere pintar los altavoces o las rejillas deberá hacerlo antes de la instalación de la rejilla. Consulte las instrucciones para pintarlos.

5.Si el altavoz se ha montado en posición horizontal, quite el logo encajable y vuelva a colo- carlo a lo largo del eje largo de la rejilla.

6.Inserte la rejilla en las ranuras del bafle presionando ligera- mente en los extremos.

Toutes installations

1.Dénudez 13 mm de câble, et torsadez les fils souples ensem- ble. La fiche de l’enceinte HSi accepte les câbles dénudés d’un diamètre maximum de 12, ou les fiches bananes simples.

2.Connectez le câble à l’enceinte.

3.Introduisez l’enceinte dans l’orifice découpé comme illus- tré ci-dessous. Les enceintes doivent être introduites dans le mur « côté woofer » en pre- mier.

4.Revissez les vis de fixation.

Important : Ne resserrez pas les vis excessivement.

Si vous voulez peindre les enceintes ou les grilles, faites-le avant l’installation des grilles. Veuillez consulter les instructions de peinture qui suivent.

5.Si l’enceinte a été installée horizontalement, retirez le logo, puis remettez-le le long de l’axe de la grille.

6.Insérez la grille dans les fentes du haut-parleur à membrane en appuyant légèrement sur ses bords.

Alle Installationen

1.13 mm Isolierung vom Kabel

entmanteln, und die Drahtlitzen zusammendrehen. Der HSi-Lautsprecheranschluss nimmt entweder blanken Draht bis zu AWG 12 oder ein- fache Gabelschuhstecker auf.

2.Das Kabel an den Lautsprecher anschließen.

3.Den Lautsprecher - wie abge- bildet - in den Ausschnitt schieben. Den Lautsprecher müssen mit der „Woofer“-Seite zuerst in die Wand geschoben werden.

4.Die Kreuzschlitz-Befestigungs- schrauben festziehen.

Wichtig: Die Schrauben nicht zu fest anziehen.

Wenn die Lautsprecher oder Ziergitter lackiert werden sollen, muss dies vor der Installation des Ziergitters geschehen (siehe Anweisungen zum Lackieren).

5.Wenn der Lautsprecher in hori- zontaler Position montiert wurde, entfernen Sie das mit einem Bindestift befestigte Logo und bringen es entlang der langen Achse des Ziergitters an.

6.Fügen Sie das Ziergitter in die Schlitze in der Schallwand ein, indem Sie entlang der Kante vorsichtig andrücken.

– 8 –

HSi N545W2 specifications

The Boston Acoustics HSi N545W2 is a remarkable addition to the world of high-fidelity audio, designed to deliver an immersive sound experience for music enthusiasts and home theater aficionados alike. This premium speaker embodies a balanced combination of sophisticated engineering, elegant design, and advanced technology, making it a standout choice in its category.

One of the defining features of the HSi N545W2 is its dual 5.25-inch woofers, which utilize a polypropylene cone for a smooth and deep bass response. This design ensures that low frequencies are reproduced accurately, providing a robust foundation for musical notes and cinematic soundtracks. Complementing the woofers is a 1-inch soft dome tweeter that produces crisp and detailed highs. This combination results in a frequency response range that covers the essential sonic spectrum, making the speaker versatile for various types of audio content.

The HSi N545W2 also employs Boston Acoustics' proprietary technologies, including the use of advanced Waveguide technology in its tweeter design. This innovation ensures an even dispersion of high frequencies across a wide listening area, promoting a more immersive soundstage. It helps to eliminate the 'sweet spot' effect, allowing listeners to enjoy high-quality audio from various positions within the room.

The cabinet design of the HSi N545W2 is another highlight. Crafted from high-quality MDF (medium-density fiberboard), it minimizes unwanted vibrations and resonances, resulting in a cleaner sound. The speaker is also designed with a modern aesthetic, featuring a sleek finish that makes it an elegant addition to any home décor. Its compact size and slim profile allow for easy integration into various environments, whether mounted on walls or placed on shelves.

Moreover, the HSi N545W2 is engineered for efficient power handling and compatibility with various audio systems. With a recommended amplifier power range and nominal impedance, it is designed to work seamlessly with both low-powered and high-powered amplifiers, making it a versatile option for audiophiles.

In summary, the Boston Acoustics HSi N545W2 is a finely-tuned speaker that embodies a blend of performance and style. With its advanced technologies, quality materials, and thoughtful design, it offers an exceptional audio experience that caters to both casual listeners and serious music connoisseurs. Whether enhancing a home theater system or enriching everyday music listening, the HSi N545W2 proves to be an impressive choice.