Installation Instructions

Installation Tips (cont.)

WARNING

Always turn off the amplifier or receiver when connecting speakers or any other components to the system.

NOTE

This manual assumes the installer possesses skill in the proper use of hand and power tools, knowledge of local building and fire codes, and a familiarity with the environment behind the wall or ceiling in which the speakers will be installed.

Tools You’ll Need

1.A utility knife, jig saw, or other tool for cutting the required hole in the mounting surface.

2.A #2 Phillips screwdriver.

3.A wire cutter or stripper for preparing the speaker wires.

4.A pencil.

Retrofit Installations

1.Mark the outline of the installation hole using the supplied template. Make a small hole at the center of the speaker location. Insert a long, bent piece of wire and rotate to confirm that there are no obstructions behind the chosen location.

2.Cut the installation hole.

Note: The flange of the speaker face is very narrow. Be very careful to cut the hole accurately.

3.Run the wire from the amplifier location to the cutout. Allow for an extra foot of wire at the cutout.

All Installations

Connecting the Speakers

Unscrew the fasteners on the back of the speaker that hold the wire clamp in place. Open up the clamp and insert about 2” (50mm) of wire through the opening. Tighten the clamp screws to secure the wire. Note: If there is a jacket around the two wire conductors fasten the clamp to the jacketed part of the wire. Remove the jacket from the part of the wire that extends beyond the clamp.

Separate the two conductors of the wire. Remove about 3⁄8” (10mm) of insulation from the end of the wire. Insert the wires into the appropriate terminals

Consejos para el montaje (cont.)

Instrucciones para la instalación

ADVERTENCIA

Apague siempre el amplificador o el receptor al conectar parlantes o cualquier otro componente al sistema.

NOTA

En este manual se presupone que el instalador posee habilidad en el manejo de herramientas manuales y eléctricas, conocimiento sobre los códigos vigentes de construcción local y normas sobre incendios y que está familiarizado con el entorno que se encuentra del otro lado de la pared o el techo en los que se instalarán los parlantes.

Herramientas necesarias

1.Una navaja multiusos, una sierra caladora u otra herramienta para cortar el agujero adecuado en la superficie de montaje.

2.Un destornillador Phillips o de cruz número 2.

3.Un cortador de alambre o pelacables para preparar el cableado de los parlantes.

4.Un lápiz.

Instalaciones en construcciones ya existentes

1.Marque el contorno del agujero de montaje con la plantilla suministrada. Haga un pequeño agujero en el centro de la ubicación del parlante. Inserte un alambre largo y curvado y déle vueltas para confirmar que no hay obstrucciones detrás de la ubicación elegida.

2.Corte el agujero para la instalación.

Nota: La pestaña en el frente del parlante es muy angosta. Tenga mucho cuidado para cortar el agujero con precisión.

3.Tienda el cable desde el amplificador hasta el agujero. Deje un pie adicional de cable en el agujero.

Todas las instalaciones

Conexión de los parlantes

Desatornille los sujetadores de la parte trasera del parlante que fijan la abrazadera del cable en su lugar. Abra la abrazadera e inserte aproximadamente 2”(50mm) de cable a través de la abertura. Apriete los tornillos de la abrazadera para sujetar el cable. Nota: Si hay una envoltura alrededor de los conductores de dos cables, ajuste la abrazadera a la parte forrada del cable. Quite la envoltura de la parte del cable que se extiende más allá de la abrazadera.

Conseils d’installation (suite)

Instructions d’installation

AVERTISSEMENT

Débranchez toujours l’amplificateur ou le récepteur avant de connecter les enceintes ou tout autre composant au système.

NOTE

Ce manuel suppose que l’installateur sait utiliser les outils manuels et électriques nécessaires à l’installation, qu’il connaît la réglementation en vigueur sur la construction et l’incendie, et qu’il sait exactement quels éléments sont situés derrière les murs ou les plafonds sur lesquels les enceintes seront fixées.

Outils nécessaires

1.Un couteau à lame rétractable, une scie sauteuse ou tout autre outil capable de découper l’orifice nécessaire dans la surface de montage.

2.Un tournevis cruciforme No. 2.

3.Une pince coupante ou un outil à dénuder pour préparer les fils des enceintes.

4.Un crayon.

Installations anciennes améliorées

1.Tracez le contour de l’orifice d’installation en utilisant le gabarit fourni. Faites un petit trou au centre de l’endroit où sera placée l’enceinte. Insérez une longue tige tordue et déplacez-la à l’intérieur pour confirmer l’absence d’obstruction derrière l’emplacement choisi.

2.Coupez l’orifice d’installation.

Note : Le panneau frontal de l’enceinte est très étroit. Prenez garde de réaliser la découpe avec précision.

3.Amenez le câble de l’amplificateur jusqu’à l’orifice en prévoyant 30 cm de fil supplémentaire.

Toutes installations

Branchement des enceintes

Dévissez les fixations qui maintiennent le serre- fils à l’arrière de l’enceinte. Ouvrez le serre-fils et insérez environ 50mm de fil à travers l’ouverture. Serrez les vis de serrage pour bloquer le fil. Note : Si les deux conducteurs de fil sont pourvus de gaines, fixez le serre-fils à la partie gainée du fil. Retirez la gaine de la partie du fil qui dépasse le serre-fils.

Séparez les deux conducteurs du fil. À l’extrémité du fil, dénudez la gaine sur environ 10mm. Insérez les fils dans les bornes appropriées du connecteur

– 8 –

HSi 430CV, HSi 435CV specifications

Boston Acoustics has long been recognized for its commitment to delivering high-quality audio products, and the HSi 435CV and HSi 430CV floorstanding speakers are no exceptions. These speakers exemplify the brand’s pursuit of precision, clarity, and a balanced sound that appeals to both audiophiles and casual listeners alike.

The Boston Acoustics HSi 435CV is a tower speaker that stands out with its impressive sonic performance. One of its main features includes a 5.25-inch polypropylene woofer, which is designed to deliver deep and resonant bass, making it perfect for both music and movie experiences. The speaker also incorporates a 1-inch copper-clad aluminum dome tweeter that extends the high-frequency response, ensuring a clear and articulate sound across the spectrum. This combination results in a well-rounded audio output that can fill a room with dynamic sound.

On the other hand, the HSi 430CV features a slightly smaller footprint but still packs a powerful punch. It employs a similar driver configuration with a 4.5-inch polypropylene woofer and a 1-inch aluminum dome tweeter, providing an excellent balance between compact design and robust sound quality. Both models utilize Boston Acoustics’ proprietary technologies, including their advanced crossover network, which ensures seamless integration between the woofer and tweeter for smooth frequency transitions.

The HSi 435CV and HSi 430CV incorporate an innovative speaker cabinet design that minimizes resonance, allowing for a purer audio experience. The enclosures are crafted using high-quality MDF, which contributes to enhanced durability and reduced distortion. The speakers also feature a stylish, modern aesthetic that can blend seamlessly into any home décor, available in classic finishes that appeal to a wide array of tastes.

Additionally, both models are engineered for compatibility with a variety of audio setups, making them an excellent choice for home theater enthusiasts looking to enhance their systems. With their impressive power handling capabilities and high sensitivity ratings, these speakers can deliver an immersive listening experience in diverse environments.

In summary, the Boston Acoustics HSi 435CV and HSi 430CV speakers exemplify the brand's commitment to quality. With their advanced driver technology, durable cabinets, and elegant design, these models promise to elevate any audio experience. Whether for music, movies, or gaming, these speakers are capable of delivering sound that captivates and entertains, making them a valuable addition to any sound system.