Bolens 930 SWE Important Safe Operation Practices, California Proposition Training, Preparation

Page 3

Important Safe Operation Practices

2

WARNING! This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury.

When you see this symbol. HEED ITS WARNING!

California Proposition 65

WARNING! Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the safe operation practices in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating fingers, hands, toes and feet and throwing foreign objects. Failure to observe the following safety instructions could result in serious injury or death.

Training

1.Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

2.Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.

3.Never allow children under 14 years of age to operate this machine. Children 14 and over should read and understand the instructions and safe operation practices in this manual and on the machine and be trained and supervised by an adult.

4.Never allow adults to operate this machine without proper instruction.

5.Thrown objects can cause serious personal injury. Plan your snow-throwing pattern to avoid discharge of material toward roads, bystanders and the like.

6.Keep bystanders, helpers, pets and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

7.Exercise caution to avoid slipping or falling, especially when operating in reverse.

Preparation

Thoroughly inspect the area where the equipment is to be used. Remove all doormats, newspapers, sleds, boards, wires and other foreign objects, which could be tripped over or thrown by the auger/impeller.

1.Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ricochet can cause serious injury to the eyes.

2.Do not operate without wearing adequate winter outer garments. Do not wear jewelry, long scarves or other loose clothing, which could become entangled in moving parts. Wear footwear which will improve footing on slippery surfaces.

3.Use a grounded three-wire extension cord and receptacle for all machines with electric start engines.

4.Adjust collector housing height to clear gravel or crushed rock surfaces.

5.Disengage all control levers before starting the engine.

6.Never attempt to make any adjustments while engine is running, except where specifically recommended in the operator’s manual.

7.Let engine and machine adjust to outdoor temperature before starting to clear snow.

Image 3
Contents July Operator’s ManualRecord Product Information Table of ContentsTo The Owner Thank YouImportant Safe Operation Practices California Proposition TrainingPreparation Safe Handling of Gasoline OperationAverage Useful Life Maintenance & StorageDo not modify engine Spark ArrestorAssembly & Set-Up Contents of CartonAssembly Headlight Harness Shear PinsChute Clean-Out Tool Set-UpAdjustments Auger and Drive Control Cables Testing Auger Drive ControlSkid Shoes Gas & Oil Fill-Up Testing Drive Control & Shift LeverIgnition Key Controls and FeaturesShift Lever Choke ControlPrimer Bulb Electric Starter SwitchChute Assembly Throttle ControlWheel Steering Controls Chute Clean-Out ToolTwo-Way Chute Control Chute Directional ControlElectric Starter OperationStarting The Engine Stopping The EngineOperating Tips Replacing Shear PinsTo Engage Drive To Engage AugersMaintenance & Adjustments MaintenanceLubrication Augers Chute Bracket AdjustmentAuger Shaft Shift CableDrive Control Auger ControlTire Pressure Belt Removal Preparation ServiceBelt Replacement Auger Belt ReplacementPulley Slot Changing Friction Wheel Drive Belt ReplacementOff-Season Storage Short-Term StorageLong-Term Storage Problem Cause Remedy TroubleshootingComponent Description Part Number Inch Replacement PartsSnow throwers CUB Cadet LLC MANUFACTURER’S Limited Warranty for