Bolens MTD warranty Standard Skid Shoe, Reversible Skid Shoe

Page 15

2.With the drive control released, there must be 1/8” clearance between the friction wheel and the drive pulley in all positions of the shift lever.

3.With the drive control engaged, the friction wheel must contact the drive pulley.

4.If adjustment is necessary, loosen the lower hex nut on the drive cable index bracket and pivot the bracket upward or downward as necessary. Refer to Figure 15. Tighten the lower hex nut to secure the bracket when correct adjustment is reached.

5.Reassemble the frame cover and turn the unit back to its operating position.

NOTE: If you placed plastic under the gas cap, be certain to remove it now.

Skid Shoes

The space between this shave plate and the ground can be adjusted. For close snow removal, place skid shoes in the low position. Use middle or high position when area to be cleared is uneven.

1.Adjust skid shoes by loosening the four lock nuts and carriage bolts and moving skid shoes to desired position. See Figure 16A or 16B.

2.Make certain the entire bottom surface of skid shoes are against the ground to avoid uneven wear on the skid shoes.

3.Tighten nuts and bolts securely.

NOTE: Some models are equipped with reversible skid shoes and may be turned over to increase their lifespan. See Figure 16B.

Auger Control

To adjust the auger control, refer to page 13.

Figure 16A - Standard Skid Shoe

Figure 16B - Reversible Skid Shoe

5

Making

Adjustments

IMPORTANT

It is not recommended that you operate this snow thrower on gravel as loose gravel can be easily picked up and thrown by the auger causing personal injury or damage to the snow thrower.

If for some reason, you have to operate the snow thrower on gravel, keep the skid shoe in the highest position for maximum clearance between the ground and the shave plate.

15

Image 15

Contents Two-Stage Snow Thrower OPERATOR’S ManualTable of Contents Finding and Recording Model NumberCustomer Support Your Responsibility Restrict the use Chute Clean-out ToolSafe Operation Do not modify engine OperationTighten hand knobs securing upper handle to lower handle Setting Up Your Snow ThrowerShear Pin Storage Prior to operatingTest on Instructions careAll models Drift Cutters If EquippedTire Pressure Pneumatic Tires Clean-Out ToolClean-Out Tool Skid ShoesKnow Your Snow Thrower Ignition Key Auger ControlDrive Control/ Auger Control Lock Four-Way Chute ControlRecoil Starter Electric Starter on certain modelsStarting The Engine Electric Starter on certain modelsAuger Control Test Recoil StarterDrive Control & Shift Lever Making AdjustmentsShift Cable Chute ControlReversible Skid Shoe Standard Skid ShoeEngine LubricationShave Plate and Skid Shoes Auger Belt Replacement Drive Belt Replacement Friction Wheel Removal Wipe equipment with an oiled rag to prevent rust Off-Season StorageProblem Cause Remedy TWO Year Supreme Warranty Part Description RÉF Pièce 17 9 Part Description RÉF Pièce 2112 23 14 5952 Carter de la collet avec trou pour raccord de graissage Page 31A-6006 Roue Jante Batterie la sur jours dix-vingt-quatre de complète Garantie Accidentel ouDépannage Solution Causes ProblèmePropre et SouffleuseCarburant le Videz Gaz Suit comme procédez caoutchouc Dégât Tout .ordinairesHex boulons des par Tarières des lementTransmission De courroie la de Remplacement’oubliez Videz Tarière la de courroie la de Remplacement’essence ’essence bouchonPatins et plate Lame LubriﬁcationMoteur Réversible Patin 16B Figure Ordinaire Patin 16A Figure Tarière la de CommandeRéglages PatinsEt transmission la de Commande Goulotte la de CommandeVitesses de levier Lanceur à Démarreur Soigneu Suivez .conducteur le blesser Modèles certains sur électrique DémarreurÉlectrique démarreur le d’utiliser Avant instructions les toutes sement’huile Plein Soufﬂeuse la de Commandes Départ de VoletFaites Ne Pièce Cette Général d’ordre RecommandationsPneus des Pression Goulotte la de dégagement de OutilStock en disponibilité la et prix les concernant gnement Échéant cas le coupe de BarresDe goupille la de Remisage CisaillementEmployer à moteur à l’huile à et carburant au Quant moteur du d’utilisation notice la consulter veuillez’assemblage Après .ESSENCE Sans mais d’huile plein Sécurité de Consignes Votre UtilisationResponsabilité Votre Goulotte la de dégagement deUnoutilGoulotte la ed Dégagement De Outil Modèle le sur série de numéro le et modèle de numéro le Vente-après ServiceModèle de numéro le trouver Pour Matières des TablePhases deux neige à Soufﬂeuse 15/2005772C0774