Bolens 31AE6GKF500 warranty To Engage Drive, To Engage Augers, Auger Control Test

Page 11

To Engage Drive

1.With the engine running near top speed, move shift lever to one of six FORWARD positions or two REVERSE positions. Select a speed appropriate for the snow conditions that exist. Do not shift speeds while the drive is engaged.

2.Squeeze drive control against the right handle and the snow thrower will move. Release it and the drive motion will stop.

To Engage Augers

1.To engage augers and start snow throwing, squeeze the left hand auger control against the left handle. Release to stop augers.

2.While the auger control is engaged, squeeze the drive control to move, release to stop. Do not shift speeds while the drive is engaged.

NOTE: This drive lever also locks auger control so you can turn the chute control without interrupting the snow throwing process.

3.Release the auger control; the interlock mechanism should keep the auger control engaged until the drive control is released.

4.Release the drive control to stop both the augers and the wheel drive. To stop the auger, both levers must be released.

Auger Control Test

Perform the following test before operating your snow thrower for the first time and at the start of each winter. Check the adjustment of the auger control as follows:

1.When the auger control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

2.In a well-ventilated area, start the snow thrower engine as instructed on the previous page. Make sure the throttle is set in the FAST position.

3.While standing in the operator’s position (behind the snow thrower), engage the auger.

4.Allow the auger to remain engaged for approximately ten (10) seconds before releasing the auger control. Repeat this several times.

5.With the auger control in the disengaged “up” posi- tion, walk to the front of the machine.

Figure 4-2

6.Confirm that the auger has completely stopped rotating and shows NO signs of motion. If the auger shows ANY signs of rotating, immediately return to the operator’s position and shut off the engine. Wait for ALL moving parts to stop before re-adjusting the auger control.

7.To readjust the control cable, loosen the upper hex nut on the auger cable bracket. See Figure 4-2.

8.Position the bracket upward to provide more slack (or downward to increase cable tension).

9.Retighten the upper hex nut.

10.Repeat Auger Control Test to verify proper adjustment has been achieved.

WARNING

The muffler, engine and surrounding areas become hot and can cause a burn 150°F (65°C). Do not touch.

When selecting a Drive Speed, use the slower speeds until you are comfortable and familiar with the operation of the snow thrower.

NEVER reposition the shift lever (change speeds or direction of travel) without first releasing the drive control and bringing the snow thrower

to a complete stop. Doing so will result in premature wear to the snow thrower’s drive system.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents 07/09/08 Two-Stage Snow Thrower769-04208 Customer Support Table of ContentsFinding and Recording Model Number Your Responsibility Restrict the use Safety SymbolsThere are rotating blades inside Do not use the engine’s electric starter in the rainYour Responsibility Safe Operation PracticesTraining PreparationAverage Useful Life Maintenance & StorageOperation Do not modify engineSetting Up Your Snow Thrower Drift Cutters If Equipped Clean-Out ToolLamp Wiring Harness If equipped Shear Pin Storage optionalKnow Your Snow Thrower Operating Your Snow Thrower$26% #/.42 Engines with Starter Handle non-electric start Gas & Oil Fill-UpStarting the Engine Stopping the EngineAuger Control Test To Engage DriveTo Engage Augers Drive Control & Shift Lever Making AdjustmentsShift Cable Chute ControlTo adjust the auger control, refer to You can also check the adjustment as followsSpace between the skid shoes and the ground can be adjusted To adjust the skid shoesAugers Maintaining Your Snow ThrowerEngine LubricationUnhook the support bracket spring from the frame Auger Belt ReplacementRoll the auger belt off the engine pulley. See Figure To inspect the friction wheel, proceed as follows Drive Belt ReplacementFriction Wheel Inspection Remove and replace belt in the reverse orderProblem Cause Remedy Trouble Shooting12.08.06 WarrantyAuger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières 42C Optional/en optionPart RÉF Pièce Description Remarque Lhabitacle peut être légèrement différent 5952 30 in/poPart Description RÉF Pièce 31AE6GKF500 La page 2 pour ce qui concerne les pièces et/ou accessoires Parts List Pièces DétachéesFor parts and/or accessories refer to customer support on Adressez-vous au «Service après-vente»Way Chute Control with tall chute Manual Chute ControlPart RÉF Pièce Description Page Page 06.08.12 GarantieDépannage Solution Causes ProblèmeSouffleuse Remisage de InstructionsPropre Souffleuse Transmission de courroie la de RemplacementVis la REMARQUEréinstaller de PAS N’oubliez Tarières La de courroie la de RemplacementPatins et plate Lame TarièreRéglages Vitesses de changement de Câble Et transmission la de CommandeGoulotte la de Commande Vitesses de levierMoteur du Arrêt Faites Ne Moteur du marche en Mise’huile et d’essence Pleins ÉlectriqueGoulotte la de dégagement de Outil Fonctions 4 à goulotte la de CommandeRoues des d’orientation Commande PhareLa sur consignes Souffleuse la de CommandesAmorçeur Explosif sont peurs Va les et inflammableÉchéant cas le Phare du câblage de FaisceauPneus des Pression Option en cisaillement De goupille la de RemisageLes Remarque Cette RemarqueGaz de émissions les concernant Avis Remisage et EntretienResponsabilité Votre Moyenne utile vie de Durée’essence de Manipulation PréparationFormation VotreMachine la d’utiliser Sécurité de Symboles’utilisation La voir détachées Pièces Vente-après ServiceModèle de numéro le trouver Pour Matières des Table07/09/08 04208-769 Phases deux neige à Souffleuse

31AE6GKF500 specifications

The Bolens 31AE6GKF500 is a standout model in the realm of outdoor power equipment, particularly designed for homeowners looking for a reliable and efficient lawn tractor. This machine combines innovative technology with a robust construction, catering to various landscaping tasks while ensuring superior performance.

One of the most prominent features of the Bolens 31AE6GKF500 is its powerful engine. Equipped with a reliable 382 cc OHV engine, this tractor provides ample power to tackle even the most challenging terrain. The engine is designed for easy starting and fuel efficiency, making it a practical choice for homeowners. The 31AE6GKF500 also features a hydrostatic transmission, which delivers smooth and responsive shifting without the need for manual gear changes. This allows users to focus on their mowing tasks without the interruption of gear management.

The cutting deck is another significant highlight of this lawn tractor. The 31AE6GKF500 hosts a 30-inch cutting deck, designed to provide a clean and even cut. This size is particularly advantageous for homeowners with smaller lawns or those navigating tighter spaces. The deck offers multiple cutting heights, allowing users to adjust the mower to suit their lawn's specific needs. This flexibility encourages a healthier lawn by promoting better grass growth.

In addition to its cutting capabilities, the Bolens 31AE6GKF500 is designed with user comfort in mind. It features a high-back padded seat, providing support during extended mowing sessions. The ergonomically designed controls are easily accessible, ensuring that users can operate the tractor with minimal effort. Furthermore, the compact size of the tractor ensures excellent maneuverability, making it easy to navigate around flower beds, trees, and other obstacles.

Maintenance is also a breeze with the Bolens 31AE6GKF500. It is designed for easy access to engine components, ensuring that routine maintenance tasks such as oil changes and air filter replacements can be performed with minimal hassle. The durable construction further guarantees longevity, allowing this lawn tractor to withstand the rigors of regular use.

Overall, the Bolens 31AE6GKF500 stands out as an excellent choice for homeowners seeking efficiency and reliability in their lawn care equipment. Its powerful engine, innovative cutting deck, user-friendly design, and easy maintenance make it a valuable addition to any outdoor toolkit. Whether you're mowing the lawn, navigating tight spaces, or simply maintaining your yard, the Bolens 31AE6GKF500 proves to be a dependable partner in achieving a well-manicured landscape.
Top Page Image Contents