Bolens 31AE6GKF500 Making Adjustments, Shift Cable, Chute Control, Drive Control & Shift Lever

Page 12

5

Making

Adjustments

WARNING

Read, understand, and follow all instruc- tions and warnings on the machine and in this manual before operating.

Never attempt to make any adjust- ments while the engine is running, except where speci- fied in operator’s manual.

Figure 5-1

Figure 5-2

Figure 5-3

Shift Cable

If the full range of speeds (forward and reverse) cannot be achieved, refer to the figure to the left and adjust the shift cable as follows:

1.Place the shift lever in the fastest forward speed position.

2.Loosen the hex nut on the shift cable index bracket. See Figure 5-1.

3.Pivot the bracket downward to take up slack in the cable.

4.Retighten the hex nut.

5.Check for correct adjustment before operating the snow thrower.

Chute Control

Once a season or every 25 hours of operation, whichever is earlier, check whether the four-way chute control™ cables have slackened. If the chute does not rotate fully, the chute control cables will have to be adjusted.

To adjust these cables, proceed as follows:

1.To tighten cable, loosen the top nut and tighten the bottom nut on the cable.

2.Adjust equally on both sides by working on both cables. See Figure 5-2.

Drive Control & Shift Lever

When the drive control is released and in the disengaged “up” position, the cable should have very little slack. It should NOT be tight.

Check the adjustment of the drive control as follows:

1.With the drive control released, push the snow thrower gently forward. The unit should roll freely.

2.Engage the drive control and gently attempt to push the snow thrower forward. The wheels should not turn. The unit should not roll freely.

3.With the drive control released, move the shift lever back and forth between the R2 position and the F6 position several times. There should be no resistance in the shift lever.

4.If any of the above tests failed, the drive cable is in need of adjustment. Proceed as follows:

5.Loosen the lower hex nut on the drive cable bracket. See Figure 5-3.

6.Position the bracket upward to provide more slack (or downward to increase cable tension).

7.Retighten the lower hex nut.

WARNING: Run the engine com- pletely dry of gasoline before tipping snowthrower.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Two-Stage Snow Thrower 769-0420807/09/08 Table of Contents Finding and Recording Model NumberCustomer Support Safety Symbols There are rotating blades insideDo not use the engine’s electric starter in the rain Your Responsibility Restrict the useSafe Operation Practices TrainingPreparation Your ResponsibilityMaintenance & Storage OperationDo not modify engine Average Useful LifeSetting Up Your Snow Thrower Clean-Out Tool Lamp Wiring Harness If equippedShear Pin Storage optional Drift Cutters If EquippedOperating Your Snow Thrower Know Your Snow Thrower$26% #/.42 Gas & Oil Fill-Up Starting the EngineStopping the Engine Engines with Starter Handle non-electric startTo Engage Drive To Engage AugersAuger Control Test Making Adjustments Shift CableChute Control Drive Control & Shift LeverYou can also check the adjustment as follows Space between the skid shoes and the ground can be adjustedTo adjust the skid shoes To adjust the auger control, refer toMaintaining Your Snow Thrower EngineLubrication AugersAuger Belt Replacement Roll the auger belt off the engine pulley. See FigureUnhook the support bracket spring from the frame Drive Belt Replacement Friction Wheel InspectionRemove and replace belt in the reverse order To inspect the friction wheel, proceed as followsTrouble Shooting Problem Cause RemedyWarranty 12.08.06Auger Housing COMPONENTS/COMPOSANTS DU Logement DES Tarières Optional/en option 42CPart RÉF Pièce Description 30 in/po Remarque Lhabitacle peut être légèrement différent 5952Part Description RÉF Pièce 31AE6GKF500 Parts List Pièces Détachées For parts and/or accessories refer to customer support onAdressez-vous au «Service après-vente» La page 2 pour ce qui concerne les pièces et/ou accessoiresManual Chute Control Way Chute Control with tall chutePart RÉF Pièce Description Page Page Garantie 06.08.12Solution Causes Problème DépannageRemisage de Instructions PropreSouffleuse Transmission de courroie la de Remplacement SouffleuseVis la REMARQUEréinstaller de PAS N’oubliez La de courroie la de Remplacement Patins et plate LameTarière TarièresRéglages Et transmission la de Commande Goulotte la de CommandeVitesses de levier Vitesses de changement de CâbleMoteur du Arrêt Moteur du marche en Mise ’huile et d’essence PleinsÉlectrique Faites NeFonctions 4 à goulotte la de Commande Roues des d’orientation CommandePhare Goulotte la de dégagement de OutilSouffleuse la de Commandes AmorçeurExplosif sont peurs Va les et inflammable La sur consignesPhare du câblage de Faisceau Pneus des PressionOption en cisaillement De goupille la de Remisage Échéant cas leCette Remarque Les RemarqueRemisage et Entretien Responsabilité VotreMoyenne utile vie de Durée Gaz de émissions les concernant AvisPréparation FormationVotre ’essence de ManipulationSécurité de Symboles Machine la d’utiliserVente-après Service Modèle de numéro le trouver PourMatières des Table ’utilisation La voir détachées PiècesPhases deux neige à Souffleuse 07/09/08 04208-769

31AE6GKF500 specifications

The Bolens 31AE6GKF500 is a standout model in the realm of outdoor power equipment, particularly designed for homeowners looking for a reliable and efficient lawn tractor. This machine combines innovative technology with a robust construction, catering to various landscaping tasks while ensuring superior performance.

One of the most prominent features of the Bolens 31AE6GKF500 is its powerful engine. Equipped with a reliable 382 cc OHV engine, this tractor provides ample power to tackle even the most challenging terrain. The engine is designed for easy starting and fuel efficiency, making it a practical choice for homeowners. The 31AE6GKF500 also features a hydrostatic transmission, which delivers smooth and responsive shifting without the need for manual gear changes. This allows users to focus on their mowing tasks without the interruption of gear management.

The cutting deck is another significant highlight of this lawn tractor. The 31AE6GKF500 hosts a 30-inch cutting deck, designed to provide a clean and even cut. This size is particularly advantageous for homeowners with smaller lawns or those navigating tighter spaces. The deck offers multiple cutting heights, allowing users to adjust the mower to suit their lawn's specific needs. This flexibility encourages a healthier lawn by promoting better grass growth.

In addition to its cutting capabilities, the Bolens 31AE6GKF500 is designed with user comfort in mind. It features a high-back padded seat, providing support during extended mowing sessions. The ergonomically designed controls are easily accessible, ensuring that users can operate the tractor with minimal effort. Furthermore, the compact size of the tractor ensures excellent maneuverability, making it easy to navigate around flower beds, trees, and other obstacles.

Maintenance is also a breeze with the Bolens 31AE6GKF500. It is designed for easy access to engine components, ensuring that routine maintenance tasks such as oil changes and air filter replacements can be performed with minimal hassle. The durable construction further guarantees longevity, allowing this lawn tractor to withstand the rigors of regular use.

Overall, the Bolens 31AE6GKF500 stands out as an excellent choice for homeowners seeking efficiency and reliability in their lawn care equipment. Its powerful engine, innovative cutting deck, user-friendly design, and easy maintenance make it a valuable addition to any outdoor toolkit. Whether you're mowing the lawn, navigating tight spaces, or simply maintaining your yard, the Bolens 31AE6GKF500 proves to be a dependable partner in achieving a well-manicured landscape.
Top Page Image Contents