Shindaiwa 80045, 75RS manual Assembly, Shindaiwa Limited Warranty

Assembly

1/4-20 x 2 1/4

Shindaiwa Limited Warranty

Hex Bolt

1/4-20

Hex Nut

RH Handle
Brace	LH Handle
Figure 1	Brace

1.Remove the spreader and compo- nents from the carton and place the spreader upside down on a padded surface. Install the LH & RH handle braces to frame using four 1/4-20 x 2 1/4" hex bolts and nuts. Do not tighten at this time. See Figure 1.

Drive	5/32 x 2"
	Cotter Pin
Wheel
	5/32 x 1"
	Cotter Pin
	Free
	Wheel

Figure 2

2.Install drive wheel onto the right- hand end of the axle as viewed from the operating position. (You can identify the drive wheel by the cotter pin hole drilled in the hub). The hub must face towards frame. Align the hole in the drive wheel hub and the hole in the axle. Secure drive wheel to axle with the 5/32" x 2" cotter pin. Install the free wheel on the opposite end of the axle. Insert the 5/32" x 1" cotter pin to retain the free wheel. See Figure 2.

1/4-20 x	1/4-20 Hex
	Nut &
2 1/4"
	Washer
Bolt

Figure 3

3.Feed control knob/wire through the T-handle until the caution label touches the round hole.

See Figure 3.

DO NOT COMPRESS THE SPRING AT THIS TIME. Feed the T-handle/control wire assembly through the square handle tube towards the locator dot. See Figure 4. Secure the T- handle to the tube with (2)1/4-20 x 2 1/4" bolts, (4) flat washers, and

(2) hex nuts. See Figure 3.

1/4-20 x 2"

Hex Bolt

Handle

Tube

Dot	1/4-20
	Hex Nut

Figure 4

4.Turn the spreader upright and install the handle tube with the dot between the handle braces as shown. Install (2) 1/4 x 1 1/2" hex bolts and nuts. See Figure 4.

The feed control wire must be positioned above the handle brace bolts to operate properly. Securely tighten all nuts and bolts installed in previous steps.

Shindaiwa Inc. manufactures its products to superior quality standards to afford our customers the highest level of satisfaction. In keeping with this goal, Shindaiwa Inc. warrants this HomePro 75RS Spreader to the original purchaser as follows:

Warranty Period

1 year for Personal/Consumer use.

180 days for Commercial/ Institutional use.

90 days for rental use.

Warranty Administration

Within the covered warranty period, Shindaiwa Inc. will, at their option, repair or replace any defect in material or workmanship, without charge for parts or labor, if this product is presented at an authorized Shindaiwa dealer.

Warranty Exclusions

and Limitations

Shindaiwa Inc. assumes no responsi- bility for damages, loss, or injury resulting from:

Normal wear and tear.

Misuse or neglect.

Modification to or removal of original component parts.

This warranty is limited to the terms

stated herein. Shindaiwa Inc. dis- claims all liability for incidental or consequential damages. Some states do not allow the exclusion of inciden- tal or consequential damages, so these limitations may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.

Shindaiwa Inc. reserves the right to change the design or specifications of this product without obligation to modify previously manufactured products.

Owner’s Responsibilities.

The owner of this product shall demonstrate reasonable care in the use, maintenance, and storage of this Shindaiwa product. If a warrantable failure should occur, the owner shall deliver the product to an authorized Shindaiwa servicing dealer for correction.

To obtain warranty service, proof of purchase must be presented to the authorized Shindaiwa servicing dealer when the product is presented for repairs.

Proof of purchase must include date of purchase and the name and address of the selling dealer.

2 11