Meyer 3245, 3954, 2636 manual Pre-Operation, Drawbar & PTO Relationship

Page 8

PRE-OPERATION

WARNING: BEFORE OPERATING, READ THIS OWNERS MANUAL COMPLETELY. PAY PARTICU- LAR ATTENTION TO THE “SAFETY PRECAUTIONS” AND “SAFETY FIRST” PAGES. READ ALL SAFETY MESSAGES HIGHLIGHTED BY “SAFETY ALERT SYMBOLS” THROUGHOUT THE MANUAL.

This spreader is to be operated with 540 RPM PTO only, unless the spreader is 1000 RPM equipped. The hitch of the spreader is designed for a standard tractor drawbar. Adjust the drawbar at 13 to 17 inches above the ground. Extend or shorten the drawbar so horizontal distance from end of tractor PTO shaft to center of the hitch pin hole is 14 inches. Secure the drawbar so that the hitch pin hole is located directly below the PTO drive line. See figure 1 for location of standard measurements.

FIGURE 1. DRAWBAR & PTO RELATIONSHIP

An improperly located hitch point may cause damage to the universal joints of the PTO drive shaft. Conforming to the standard 14" drawbar & PTO relationship will ensure that the PTO drive shaft will not become over-extended.

DANGER: DO NOT OPERATE WITHOUT PTO GUARD ON SPREADER AND ON TRACTOR. MAIN- TAIN PTO DRIVE SHAFT GUARD TUBES IN OPER- ATING CONDITION. REPLACE THEM IF DAMAGED AND NOT TURNING FREELY. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.

WARNING: INSPECT REGULARLY THAT ALL CONNECTIONS AND BOLTS ARE TIGHT AND SE- CURE BEFORE OPERATING. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.

Check for proper assembly and adjustment and make sure that all bolts are tightened. Securely retighten af- ter a few hours of operation, as bolts can loosen up on new machinery. Check wheel lug nuts upon delivery and periodically thereafter. Lug nuts should be tight- ened and the tires inflated to the recommended pres- sure. Refer to the wheel torque and tire inflation chart on page 55

Inspect all adjustments on the spreader to be sure they are proper and to provide maximum performance. Lubricate the spreader completely if it is required and check the level of liquid gear grease in all three gear- boxes.

WARNING: DO NOT OPERATE WITHOUT ALL SHIELDS, GUARDS AND COVERS IN- STALLED. FAILURE TO HEED MAY RESULT IN SE- RIOUS PERSONAL INJURY OR DEATH.

Fasten the spreader hitch to the tractor drawbar with a hitch pin that cannot bounce out. Use 1" diameter hitch pin to pull spreader.

Remove the weight from the jack (jack is not to be used when spreader is loaded). Remove jack from square mount tube and move to the transport storage tube on the left front side of the frame channel. Store in a hori- zontal position.

Before operation and after hitching the tractor to the spreader, connect the PTO drive shaft to the tractor. Slide spring loaded locking collar on PTO yoke rearward, and slide yoke onto the tractor PTO shaft. Release spring loaded collar. Be sure pins fall into groove of trac- tor PTO shaft and collar snaps forward into locking posi- tion.

CAUTION: DO NOT USE A STEEL HAMMER TO AID IN JOINING PTO PARTS.

Route hydraulic hoses through the hose support rod which is mounted to the hitch frame, figure 2 . Connect the hydraulic hoses for the flow control rear gate to the tractor’s double acting valve hydraulic system. Move the tractor hydraulic controls to observe proper flow gate operation. If the controls operate the gate in op- posite directions to what you expect, reverse the hy- draulic hose connections at the tractor.

WARNING: HYDRAULIC FLUID ESCAPING UNDER PRESSURE CAN HAVE SUFFICIENT FORCE TO PENETRATE SKIN. KEEP ALL HOSES AND CONNECTIONS IN GOOD SERVICEABLE CONDITION. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.

Before loading spreader, slowly engage the tractor PTO and operate machine at idle speed for several minutes to insure the spreader is lubricated and oper- ating properly.

Model V-Max

—8—

Page 7 Page 9
Image 8
Page 7 Page 9
Contents MAX Twin Expeller Super Spreader Operators and Parts Manual no -7-V-MAXTable of Contents MANUFACTURER’S Warranty VIIIntroduction RememberSafety Precautions Study the Above Safety RulesSafety First Safety First PRE-OPERATION Drawbar & PTO RelationshipMaximum Spreader Load Weights TransportingTractor Towing Size Requirements LBS / CU. FTTruck Mount Spreaders Stalled to Retain the Connection beTween Tractor or Other Towing Vehicle Spreader Whenever Traveling onModel V-Max Unloading OperationLoading Optional Shear Sprocket IN- Structions Storage After USE DescriptionDrive Line Attachment Field Adjustment on the Cutout ClutchPTO Drive Line Normal Operation Maintenance InformationLubrication Adjustments Spinner Material GuidesSpring Loaded Adjuster Front Drive Roller ChainsIdler Nylon Roller RH Auger SprocketCompression Spring Lubrication Daily Lubrication every 8-12 loadsMonthly Lubrication Seasonal Lubrication Lubrication & Adjustment for Optional 3RD AugerAdjustments Instructions for Optional Automatic Chain Oiler Repair Parts Optional OIL-KITKEY OEM Part no Description Front Shield & Side Shaft Drive Front Shield & Side Shaft Drive Auger DRIVE, Primary Reduction KEY DescriptionAuger DRIVE, Secondary Reduction RH Auger DRIVE, Final Reduction RH Auger DRIVE, Final Reduction LH Auger DRIVE, Final Reduction LH Auger DRIVE, Final Reduction BOX, Augers & Side Shaft BOX, Augers & Side Shaft Unloading Gate & Trip PAN Doors KEY Description Spinners & Gearbox Shaft Drive KEY Description Spinner Gear Reducers HUBS, Axle & Tandem Axle Assembly KEY DescriptionOptional Third Auger KEY PTO Drive Shaft Assembly KEY Meyer Part DescriptionKEY Meyer Part no Description RPM-1-3/8, 21 Spline SP Standard PTO Drive Shaft Assembly PTO Drive Shaft Standard 540 or 1000 RPM PTO KEY Meyer Part DescriptionPTO Drive Shaft Assembly RPM KIT SVS-RPM-KIT KEY Description QTYMAX Highway Lighting Meyer Super Spreader Trouble Shooting Symptom Problem Solution AugersSymptom Problem Solution Roller Chains Meyer Super Spreader Maintenance Record Tire Size PLY PSI Meyer Equipment Wheel TorqueTire Inflation Meyer Super Spreader Specifications ModelModel V-Max Model V-Max Model V-Max

3245, 2636, 3954 specifications

Meyer 3954, 2636, and 3245 are notable models that showcase the brand's commitment to innovation, quality, and performance in the industry of advanced machinery and equipment. Each model is designed to cater to specific operational needs while incorporating cutting-edge technologies and user-friendly features.

The Meyer 3954 model is engineered primarily for heavy-duty applications, making it ideal for industrial use. This model is equipped with a robust engine that delivers optimal power and efficiency. Its key features include a high payload capacity, advanced hydraulic systems for enhanced lifting capabilities, and modular components that simplify maintenance. Furthermore, the intuitive control interface allows operators to manage tasks with precision, improving productivity and reducing operational downtime.

Moving on to the Meyer 2636, this model is tailored for versatility and agility, making it suitable for both indoor and outdoor applications. The compact design allows for easy maneuverability in tight spaces, while the advanced tracking system ensures stability and safety in various environments. The 2636 model is equipped with energy-efficient technology, significantly reducing operational costs while minimizing the environmental impact. Its user-centric design includes ergonomic controls that promote ease of use for operators.

Lastly, the Meyer 3245 stands out for its advanced technological integrations. This model features smart connectivity options, enabling real-time monitoring and diagnostics through a dedicated mobile application. Operators can access key performance metrics, receive alerts for maintenance needs, and optimize operational efficiency from anywhere. The 3245 also boasts enhanced safety features such as collision avoidance systems and automatic shutoff capabilities, making it one of the safest options in its class.

In conclusion, the Meyer 3954, 2636, and 3245 models exemplify the brand's dedication to delivering high-performance machinery tailored to diverse operational requirements. With their respective strengths, these models integrate advanced features and technologies that cater to both industrial and commercial applications, ensuring efficiency, safety, and reliability. As industries continue to evolve, Meyer remains at the forefront, providing innovative solutions that meet the challenges of modern operations.
Top Page Image Contents