Land Pride 313-308M manual Pull Tongue Hook-Up, Pull Tongue Disconnect

Page 15

Land Pride

Table of Contents

Section 2: Assembly & Set-Up (Optional)

Pull Tongue Hook-Up

Refer to Figure 1-9:

The lower link handles should be in the down position before preceding.

1.Mount Pull Tongue to tractor drawbar and secure with safety chain.

2.Connect hydraulic hoses to tractor.

3.Fully extend the lift cylinder to rase the transport wheels and lower the hitch links.

4.Back the pull tongue up to the seeder to align the hitch links with the seeder’s inside smaller pins.

5.Retract the lift cylinder to rase the hitch links up around the seeder’s inside smaller pins until the pins lock into the lower hitch links. Once the pins are locked in, adjust the lift cylinder up or down as needed to level the seeder.

6.With the seeder level and the transport wheels resting on the ground, adjust the top center link of the pull tongue so that it will install in the bottom holes of the seeder’s upper center hitch. (Top center link pin is provided by the customer)

Locking Release

Handles

Top Center Link

Pull Tongue Disconnect

!CAUTION

The seeder will have negative tongue weight when it is lifted off the ground. Lower the seeder to the ground before proceeding with Pull Tongue disconnect. (Negative tongue weight is when most of the weight is to the rear of the implement causing the front of the tongue to be light and may rise up when disconnected.)

1.Remove top link pin.

2.Flip locking release handles up on pull tongue.

3.Lower tongue until the links are free from the seeders lower pins.

Bottom Holes of

Upper Center

Hitch

Inside Smaller

Pins

Lift Cylinder

 

Hitch Link

 

 

 

20740

Pull Tongue Assembly

Figure 1-9

4/03/08

PS2096 Series Primary Seeders 313-308M

13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Primary Seeders Table of Contents Be Aware Signal Words For Your ProtectionShutdown and Storage Transport Machinery Safely Use Safety Lights and DevicesUse a Safety Chain Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Prepare for EmergenciesKeep Riders Off Machinery Wear Protective Equipment818-055C Safety Labels818-543C 838-111C818-230C 818-229CSmall Grass Seed Option 20593 Using This Manual ApplicationOwner Assistance Pre-Assembly Checklist Tire Track Remover AssemblySling Bracket Small Seeds Box S/N 397503+ Small Seeder Box assemblySmall Seeds Drive Assembly Small Seeds Box S/N Small Seeds Box Assembly12 PS2096 Series Primary Seeders 313-308M Pull Tongue Hook-Up Pull Tongue DisconnectLocking Release Handles Top Center Link Tractor Requirements General DescriptionOperating Check List Seeder PreparationParking Pull Tongue Hook-UpSeeding TransportingRoller Packing Wheels Drive SystemSeed Rate Speed Change Main Seed BoxHigh Range Low Range Seeding Adjustments Small Seeds Box Option Seed Rate Charts Fescue Fine Blade, Turf Type Pounds per AcreFescue Fine Blade, Turf Type Pounds per 1000 Square Feet Wheatgrass Crested Pounds per Acre Lovegrass Sand Pounds per AcreRye Grass Annual Pounds per Acre Rye Grass Perennial Pounds per AcreFescue Fine Blade, Turf Type Kilograms per Hectare Seed Rate Charts MetricOrchard Grass Kilograms per 1000 Square Meters Birdsfoot Trefoil Pounds per Acre Seed Rate Charts Small Seed Box OptionHours MaintenanceStorage LubricationRequired Roller ChainsDrive Sprocket Hanger Bearing Zerk PS20 Series Primary Seeder Model PS2096 Primary SeederPS 2096 Pull Type Hitch Features Benefits Problem Solution Torque Values Chart For Common Bolt Size In-tpi1· m Ft-lb Lb3 Warranty Corporate Office P.O. Box Salina, Kansas 67402-5060 USA
Top Page Image Contents