Classe Audio VSX-80TXV-S manual Using other functions Using the sleep timer, Resetting the system

Page 55

Using other functions

Using the sleep timer

The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without worrying about the receiver being left on all night. Use the remote control to set the sleep timer.

DVR 2

DVD TV DVR1 TVCTRL

		XM RADIO	ROOM 2
CD	CD-R	TUNER	RECEIVER
	SLEEP	SBch	ANALOG
			ATT
	SR+	DIMMER	MIDNIGHT/
			LOUDNESS

•Press RECEIVER then press SLEEP repeatedly to set the sleep time.

	30 min				60 min
	30 min				60 min
		Off			90 min
		Off			90 min

•You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle through the sleep options again.1

10

Resetting the system

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.

1Switch the receiver into standby.

2While holding down the front panel TONE button,

press and hold STANDBY/ON for about three seconds.

The display shows RESET?.

3Press the front panel ENTER button. The display shows RESET OK?.

4Press SYSTEM SETUP to confirm.

OK appears in the display to indicate that the receiver has been reset to the factory default settings.

•Note that all settings will be saved, even if the receiver is unplugged.

Dimming the display

You can choose between four brightness levels for the front panel display. Note that when selecting sources, the display automatically brightens for a few seconds.

		XM RADIO	ROOM 2
CD	CD-R	TUNER	RECEIVER
	SLEEP	SBch	ANALOG
			ATT
	SR+	DIMMER	MIDNIGHT/
			LOUDNESS
	DIALOG E	PHASE	S.RETRIEVER

DACCESS

•Press RECEIVER then press DIMMER repeatedly to change the brightness of the front panel display.

Switching the speaker impedance

We recommend using speakers of 8 Ω with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6 Ω impedance rating. Use the front panel controls to do this.

• With the receiver in standby, press STANDBY/ ON while holding down the SPEAKERS button. Each time you do this, you switch between the impedance settings:

•SP 6 OHM – Use this setting if your speakers are rated at 6 Ω.

•SP 8 OHM – Use this setting if your speakers are rated at 8 Ω or more.

Note

1 You can also switch off the sleep timer simply by switching off the receiver.

55

En

Image 55

Contents VSX-80TXVVSX-80TXV-S Keep in a Secure AREA. this is for Your Security Federal Communications Declaration of ConformityModel Number Responsible Party NameImportant Safety Instructions Contents Controlling the rest of your system Other SettingsUsing other functions Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterBefore you start Ventilation Installing the receiverLoading the batteries Introduction to home theater Automatically setting up for surround sound McaccMinute guide 02 5 minute guide ChapterMinute guide Speaker configuration in the OSDWait for the test tones to finish then confirm Playing a source Better sound using Basic Phase ControlProblems when using the Auto Mcacc Setup 02 5 minute guideConnecting your equipment Chapter Connecting your equipmentRear panel When making cable connections Connecting your equipmentAbout the video converter Connecting a satellite/cable receiver or other set-top box Connecting your equipment Connecting your TV and DVD playerDVD player DVR, VCR, etc Connecting a DVD/HDD recorder, VCR and other video sourcesUsing the component video jacks Use an optical cable for the connectionUse a three-way component video cable Connecting digital audio sourcesCD-R, MD, DAT, etc Tape deck, etc Connecting analog audio sourcesConnecting a component to the front panel inputs About the WMA9 Pro decoderConnecting the speakers Connecting your equipment Installing your speaker systemPlacing the speakers Bare wire connectionsBanana plug connections THX speaker system setup Connecting antennasAC outlet Connecting external antennasPlug the power cord into a power outlet Plugging in the receiverControls and displays Chapter Controls and displaysFront panel Controls and displays Operating range of remote control unitMULTI-ROOM Controls and displays DisplaySleep Over / ATTSelect Controls and displays Remote controlReceiver Input SelectMute Multi OPEShift SourceStandard surround sound Listening to your systemListening to your system Chapter Auto playback Listening in surround soundListening to your system Using the Home THX modesUsing the Advanced surround effects Setting the effect optionsUse the +/- buttons to set it as necessary Press EFFECT/CH SEL again to adjust other settingsListening with Acoustic Calibration EQ Listening in stereoUsing the Virtual Surround Back mode Listening to your system Choosing the input signalPress Tone to select the frequency you want to adjust Using Midnight and LoudnessUsing the Sound Retriever Using the tone controlsListening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAbcdefghijklmnopqrstuvwxyz Using the tunerNaming station presets Listening to station presetsSurround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu System Setup menuManual Mcacc setup Select ‘Manual MCACC’ from the System Setup menuFine Speaker Distance Setting the Acoustic Calibration EQ automaticallySelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Select ‘EQ Auto Setting’ from the Manual Mcacc setup menuSetting the Acoustic Calibration EQ manually Copying your Acoustic Calibration EQ settingsFront Align Speaker Setting Manual speaker setupChecking your Acoustic Calibration EQ settings Crossover Network Select ‘Crossover Network’ from the Manual SP Setup menuSelect ‘Channel Level’ from the Manual SP Setup menu Tip Select a setup optionSpeaker Distance THX Audio SettingSelect ‘THX Speaker Setup’ from the Manual SP Setup menu THX Speaker SetupSpecify whether or not you are using a THX speaker system Other connections Chapter Using XM RadioConnecting your XM Radio receiver Other connectionsOther connections Connecting using HdmiUsing XM HD Surround Saving channel presetsUse standard RCA/phono jack cables for the connections Connecting the multichannel analog inputsAbout Hdmi Selecting the multichannel analog inputsBi-amping your front speakers Other connections Second Zone speaker B setupSwitching the speaker system 2nd Zone setting only.1Bi-wiring your speakers Connecting additional amplifiersLarge Other connections Multi-room listening Using the multi-room controlsBasic multi-room setup Surround Back System multi-room setupPress Control Connecting an IR receiverMulti-room remote controls Use the Master Volume dial to adjust the volume12V Using this receiver with a Pioneer plasma displayAudio Using the SR+ mode with a Pioneer plasma displayDVD player DVD/LDAssigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuAssigning the Hdmi inputs Other SettingsOther Setup menu Dynamic Range Control SetupVideo Converter Setup Dual Mono SetupLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysVolt Trigger setup Multi-Room and IR receiver setupMaking an audio or a video recording Using other functionsUsing other functions Chapter Reducing the level of an analog signalDisplay shows RESET? Using other functions Using the sleep timerResetting the system Switching the speaker impedanceControlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Programming signals from other remote controlsControlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codesDirect function Multi Operation and System Off Renaming input source namesProgramming a multi-operation or a shutdown sequence Using System off Using multi operationsControls for other components Controlling the rest of your system Controls for TVsDecide which component you want to use the remote sensor Operating other Pioneer components with this unit’s sensorAdditional information Chapter TroubleshootingPower Additional informationAdditional information Other audio problemsVideo SettingsDisplay Remote controlSR cable is connected, but XM radio messagesDolby Additional information Surround sound formatsWindows Media Audio 9 Professional About THX THX MusicMode Listening modes with different input signal formatsStereo 2 channel signal formats THX Games ModeAuto Multichannel signal formatsCleaning the unit Additional information SpecificationsOnce you have established a comfortable sound level To establish a safe levelDecibel Level Example Pioneer Corporation