Classe Audio VSX-80TXV-S manual Additional information, Other audio problems

Page 63

Additional information

12

SymptomRemedy

No sound from surround back speakers.

•Check that the surround back speakers are set to LARGE or SMALL (see Speaker Setting on page 37).

•Make sure surround back processing is set to SBch ON (see Using surround back channel processing on page 29).

•If the source is Dolby Surround EX or DTS ES with no flag to indicate 6.1 compatibility, then with surround back processing set to SBch Auto, there will be no sound from the surround back speakers. In this case, set to SBch ON (see Using surround back channel processing on page 29).

•If the source does not have 6.1 playback channels, make sure that surround back processing is set to SBch ON and a surround mode is selected (see Listening in surround sound on page 26).

•Check the speaker connections (see Connecting the speakers on page 17). If only one surround back speaker is connected, make sure it’s connected to the left channel speaker terminal.

No sound from subwoofer.

• Check that the subwoofer is connected properly, switched on and the volume turned up.

 

• If your subwoofer has a sleep function, make sure it is switched off.

 

• Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 37).

 

• The crossover frequency may be set too low; try setting it higher to match the characteristics of your other

 

speakers (see Speaker Setting on page 37)

 

• If there is very little low frequency information in the source material, change your speaker settings to

 

Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (see Speaker Setting on page 37).

 

• Check the speaker level settings (see Channel Level on page 38).

No sound from one speaker.

•Check the speaker connection (see Connecting the speakers on page 17).

•Check the speaker level settings (see Channel Level on page 38).

•Check that the speaker hasn’t been set to NO (see Speaker Setting on page 37).

•The channel may not be recorded in the source. By using one of the advanced effect listening mode, you may be able to create the missing channel (see Listening in surround sound on page 26).

Sound is produced from analog

• Check that the input signal type is set to DIGITAL (see Choosing the input signal on page 29).

components, but not from digital

• Make sure that the digital input is assigned correctly for the input jack the component is connected to

ones (DVD, LD, CD-ROM etc.).

(see The Input Assign menu on page 50).

 

• Check the digital output settings on the source component.

 

• If the source component has a digital volume control, make sure this is not turned down.

 

• Make sure that the multichannel analog inputs are not selected. Select any other input source.

 

 

No sound is output or a noise is

• Check that your DVD player is compatible with Dolby Digital/DTS discs.

output when Dolby Digital/DTS

• Check the digital output settings of your DVD player. Make sure that the DTS signal output is set to On.

software is played back.

• If the source component has a digital volume control, make sure this is not turned down.

 

 

No sound when using the System

• If sound is muted in the sub room (ROOM 2), it will be restored after exiting the System Setup menu.

Setup or Status menu.

 

 

 

Other audio problems

Symptom

Remedy

Broadcast stations cannot be

For FM broadcasts

selected automatically, or there is

• Fully extend the FM wire antenna, adjust the position for best reception and secure to a wall, etc.

considerable noise in radio

• Use an outdoor antenna for better reception (see page 20).

broadcasts.

For AM broadcasts

 

• Adjust the position and direction of the AM antenna.

 

• Use an outdoor antenna for better reception (see page 20).

 

• Noise may be caused by interference from other equipment, such as a fluorescent light, motor, etc.

 

Switch off or move the other equipment, or move the AM antenna.

 

 

A multichannel DVD source

• Make sure that the multichannel analog inputs are selected (see Selecting the multichannel analog inputs

appears to be downmixed to 2

on page 43).

channels during playback.

 

Noise is output when scanning a • This is not a malfunction of the receiver. The scan function of your player alters the digital information,

DTS CD.

making it unreadable, resulting in noise being output. Lower the volume when scanning.

 

 

When playing a DTS format LD

• Make sure that the input signal type is set to DIGITAL (see Choosing the input signal on page 29).

there is audible noise on the

 

soundtrack.

 

 

 

63

En

Page 62 Page 64
Image 63
Page 62 Page 64
Contents VSX-80TXVVSX-80TXV-S Keep in a Secure AREA. this is for Your Security Federal Communications Declaration of ConformityModel Number Responsible Party NameImportant Safety Instructions Contents Controlling the rest of your system Other SettingsUsing other functions Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterInstalling the receiver Before you start VentilationLoading the batteries Introduction to home theater Automatically setting up for surround sound McaccMinute guide 02 5 minute guide ChapterSpeaker configuration in the OSD Minute guideWait for the test tones to finish then confirm Playing a source Better sound using Basic Phase ControlProblems when using the Auto Mcacc Setup 02 5 minute guideConnecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsAbout the video converter Connecting your equipment Connecting your TV and DVD player Connecting a satellite/cable receiver or other set-top boxDVD player DVR, VCR, etc Connecting a DVD/HDD recorder, VCR and other video sourcesUsing the component video jacks Use an optical cable for the connectionConnecting digital audio sources Use a three-way component video cableCD-R, MD, DAT, etc Tape deck, etc Connecting analog audio sourcesConnecting a component to the front panel inputs About the WMA9 Pro decoderConnecting the speakers Connecting your equipment Installing your speaker systemBare wire connections Placing the speakersBanana plug connections THX speaker system setup Connecting antennasAC outlet Connecting external antennasPlug the power cord into a power outlet Plugging in the receiverControls and displays Controls and displays ChapterFront panel Controls and displays Operating range of remote control unitMULTI-ROOM Controls and displays DisplaySleep Over / ATTSelect Controls and displays Remote controlReceiver Input SelectMute Multi OPEShift SourceStandard surround sound Listening to your systemListening to your system Chapter Auto playback Listening in surround soundListening to your system Using the Home THX modesUsing the Advanced surround effects Setting the effect optionsUse the +/- buttons to set it as necessary Press EFFECT/CH SEL again to adjust other settingsListening with Acoustic Calibration EQ Listening in stereoUsing the Virtual Surround Back mode Listening to your system Choosing the input signalPress Tone to select the frequency you want to adjust Using Midnight and LoudnessUsing the Sound Retriever Using the tone controlsListening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAbcdefghijklmnopqrstuvwxyz Using the tunerNaming station presets Listening to station presetsSurround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu System Setup menuManual Mcacc setup Select ‘Manual MCACC’ from the System Setup menuFine Speaker Distance Setting the Acoustic Calibration EQ automaticallySelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Select ‘EQ Auto Setting’ from the Manual Mcacc setup menuCopying your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ manuallyFront Align Manual speaker setup Speaker SettingChecking your Acoustic Calibration EQ settings Crossover Network Select ‘Crossover Network’ from the Manual SP Setup menuSelect ‘Channel Level’ from the Manual SP Setup menu Tip Select a setup optionSpeaker Distance THX Audio SettingTHX Speaker Setup Select ‘THX Speaker Setup’ from the Manual SP Setup menuSpecify whether or not you are using a THX speaker system Other connections Chapter Using XM RadioConnecting your XM Radio receiver Other connectionsOther connections Connecting using HdmiUsing XM HD Surround Saving channel presetsUse standard RCA/phono jack cables for the connections Connecting the multichannel analog inputsAbout Hdmi Selecting the multichannel analog inputsBi-amping your front speakers Other connections Second Zone speaker B setupSwitching the speaker system 2nd Zone setting only.1Connecting additional amplifiers Bi-wiring your speakersLarge Other connections Multi-room listening Using the multi-room controlsBasic multi-room setup Surround Back System multi-room setupPress Control Connecting an IR receiverMulti-room remote controls Use the Master Volume dial to adjust the volume12V Using this receiver with a Pioneer plasma displayAudio Using the SR+ mode with a Pioneer plasma displayDVD player DVD/LDAssigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuAssigning the Hdmi inputs Other SettingsOther Setup menu Dynamic Range Control SetupVideo Converter Setup Dual Mono SetupLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysVolt Trigger setup Multi-Room and IR receiver setupMaking an audio or a video recording Using other functionsUsing other functions Chapter Reducing the level of an analog signalDisplay shows RESET? Using other functions Using the sleep timerResetting the system Switching the speaker impedanceControlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Programming signals from other remote controlsControlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codesRenaming input source names Direct function Multi Operation and System OffProgramming a multi-operation or a shutdown sequence Using System off Using multi operationsControls for other components Controlling the rest of your system Controls for TVsDecide which component you want to use the remote sensor Operating other Pioneer components with this unit’s sensorAdditional information Chapter TroubleshootingPower Additional informationAdditional information Other audio problemsVideo SettingsDisplay Remote controlSR cable is connected, but XM radio messagesAdditional information Surround sound formats DolbyWindows Media Audio 9 Professional About THX THX MusicMode Listening modes with different input signal formatsStereo 2 channel signal formats THX Games ModeAuto Multichannel signal formatsCleaning the unit Additional information SpecificationsTo establish a safe level Once you have established a comfortable sound levelDecibel Level Example Pioneer Corporation
Top Page Image Contents