Classe Audio VSX-80TXV-S manual Additional information Specifications, Cleaning the unit

Page 71

Additional information

Specifications

Amplifier section

Continuous average power output of 110 watts* per channel, min., at 8 ohms, from 20 Hz to 20 000 Hz with no more than 0.09 %** total harmonic distortion (front).

Continuous Power Output (20 Hz to 20 kHz, 8 Ω, 0.09 %)

Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 W Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 W Surround back . . . . . . . . . . . . . . . . . . . . . . . . 110 W + 110 W

Continuous Power Output (1 kHz, 6 Ω, 1.0 %)

Front. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 W Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 W Surround back . . . . . . . . . . . . . . . . . . . . . . . . 150 W + 150 W

Total harmonic distortion. . . . . . . . . . . . . . . . . . . . . . . 0.09 % (20 Hz to 20 kHz, 110 W, 8 Ω)

*Measured pursuant to the Federal Trade Commission’s Trade Regulation rule on Power Output Claims for Amplifiers

**Measured by Audio Spectrum Analyzer

Audio Section

Input (Sensitivity/Impedance)

LINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .335 mV/47 kΩ

Frequency Response (LINE). . . . . . .5 Hz to 100 000 Hz dB Output (Level/Impedance)

REC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 335 mV/2.2 kΩ Tone Control

BASS . . . . . . . . . . . . . . . . . . . . . . . . . . . .± 6 dB (100 Hz) TREBLE . . . . . . . . . . . . . . . . . . . . . . . . . .± 6 dB (10 kHz) LOUDNESS. . . . . . . . . . .+4 dB / +2 dB (100 Hz/10 kHz)

(at volume position –40 dB)

Signal-to-Noise Ratio (IHF, short circuited, A network) LINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 dB

Signal-to-Noise Ratio [EIA, at 1 W (1 kHz)]

LINE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 dB

12

FM Tuner Section

Frequency Range . . . . . . . . . . . . . . . . . 87.5 MHz to 108 MHz Usable Sensitivity . . . . . . .Mono: 13.2 dBf, IHF (1.3 µV/75 Ω) 50 dB Quieting Sensitivity . . . . . . . . . . . . . . . Mono: 20.2 dBf Stereo: 38.6 dBf Signal-to-Noise Ratio . . . . . . . . . . . . Mono: 73 dB (at 85 dBf) Stereo: 70 dB (at 85 dBf)

Distortion . . . . . . . . . . . . . . . . . . . . . . . . Stereo: 0.5 % (1 kHz) Alternate Channel Selectivity . . . . . . . . . . . .60 dB (400 kHz) Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . .40 dB (1 kHz) Frequency Response . . . . . . . . . . . . . 30 Hz to 15 kHz ± 1dB Antenna Input . . . . . . . . . . . . . . . . . . . . . . . 75 Ω unbalanced

AM Tuner Section

Frequency Range . . . . . . . . . . . . . . . . . . 530 kHz to 1700 kHz Sensitivity (IHF, Loop antenna) . . . . . . . . . . . . . . . . 350 µV/m Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 dB Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 dB Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loop antenna

Miscellaneous

Power Requirements. . . . . . . . . . . . . . . . . . . .AC 120 V, 60 Hz Power Consumption . . . . . . . . . . . . . . . . . . . . . 490 W, 650 VA In standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 W AC Outlet . . . . . . . . . . . . . . . . . . . . . . (switched) 100 W MAX. Dimensions . . . . . .420 (W) mm x 173 (H) mm x 466 (D) mm

(16 9/16 (W) in. x 6 13/16 (H) in. x 18 3/8 (D) in.) Weight (without package). . . . . . . . . . . . 15.0 kg (33 lbs 1 oz)

Furnished Parts

Setup microphone (for Auto MCACC setup). . . . . . . . . . . . . 1 AA/IEC R6P dry cell batteries . . . . . . . . . . . . . . . . . . . . . . . 2 Remote control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 These operating instructions

Note

•Specifications and the design are subject to possible modifications without notice, due to improvements.

Composite Video / S-Video Section

Input (Sensitivity/Impedance) . . . . . . . . . . . . . . . .1 Vp-p/75 Ω Output (Level/Impedance) . . . . . . . . . . . . . . . . . . .1 Vp-p/75 Ω Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 dB Frequency Response . . . . . . . . . . . . . . . . . . . .5 Hz to 10 MHz

Component Video Section

Input (Sensitivity/Impedance) . . . . . . . . . . . . . . . .1 Vp-p/75 Ω Output (Level/Impedance) . . . . . . . . . . . . . . . . . . .1 Vp-p/75 Ω Signal-to-Noise Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 dB Frequency Response . . . . . . . . . . . . . . . . . . .5 Hz to 100 MHz

Cleaning the unit

•Use a polishing cloth or dry cloth to wipe off dust and dirt.

•When the surface is dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleansers.

•Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit, since these will corrode the surface.

71

En

Page 70 Page 72
Image 71
Page 70 Page 72
Contents VSX-80TXVVSX-80TXV-S Keep in a Secure AREA. this is for Your Security Federal Communications Declaration of ConformityModel Number Responsible Party NameImportant Safety Instructions Contents Controlling the rest of your system Other SettingsUsing other functions Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterLoading the batteries Installing the receiverBefore you start Ventilation Introduction to home theater Automatically setting up for surround sound McaccMinute guide 02 5 minute guide ChapterWait for the test tones to finish then confirm Speaker configuration in the OSDMinute guide Playing a source Better sound using Basic Phase ControlProblems when using the Auto Mcacc Setup 02 5 minute guideRear panel Connecting your equipmentConnecting your equipment Chapter About the video converter Connecting your equipmentWhen making cable connections DVD player Connecting your equipment Connecting your TV and DVD playerConnecting a satellite/cable receiver or other set-top box DVR, VCR, etc Connecting a DVD/HDD recorder, VCR and other video sourcesUsing the component video jacks Use an optical cable for the connectionCD-R, MD, DAT, etc Connecting digital audio sourcesUse a three-way component video cable Tape deck, etc Connecting analog audio sourcesConnecting a component to the front panel inputs About the WMA9 Pro decoderConnecting the speakers Connecting your equipment Installing your speaker systemBanana plug connections Bare wire connectionsPlacing the speakers THX speaker system setup Connecting antennasAC outlet Connecting external antennasPlug the power cord into a power outlet Plugging in the receiverFront panel Controls and displaysControls and displays Chapter Controls and displays Operating range of remote control unitMULTI-ROOM Controls and displays DisplaySleep Over / ATTSelect Controls and displays Remote controlReceiver Input SelectMute Multi OPEShift SourceStandard surround sound Listening to your systemListening to your system Chapter Auto playback Listening in surround soundListening to your system Using the Home THX modesUsing the Advanced surround effects Setting the effect optionsUse the +/- buttons to set it as necessary Press EFFECT/CH SEL again to adjust other settingsListening with Acoustic Calibration EQ Listening in stereoUsing the Virtual Surround Back mode Listening to your system Choosing the input signalPress Tone to select the frequency you want to adjust Using Midnight and LoudnessUsing the Sound Retriever Using the tone controlsListening to the radio Using the tunerUsing the tuner Chapter Saving station presetsAbcdefghijklmnopqrstuvwxyz Using the tunerNaming station presets Listening to station presetsSurround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu System Setup menuManual Mcacc setup Select ‘Manual MCACC’ from the System Setup menuFine Speaker Distance Setting the Acoustic Calibration EQ automaticallySelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Select ‘EQ Auto Setting’ from the Manual Mcacc setup menuFront Align Copying your Acoustic Calibration EQ settingsSetting the Acoustic Calibration EQ manually Checking your Acoustic Calibration EQ settings Manual speaker setupSpeaker Setting Crossover Network Select ‘Crossover Network’ from the Manual SP Setup menuSelect ‘Channel Level’ from the Manual SP Setup menu Tip Select a setup optionSpeaker Distance THX Audio SettingSpecify whether or not you are using a THX speaker system THX Speaker SetupSelect ‘THX Speaker Setup’ from the Manual SP Setup menu Other connections Chapter Using XM RadioConnecting your XM Radio receiver Other connectionsOther connections Connecting using HdmiUsing XM HD Surround Saving channel presetsUse standard RCA/phono jack cables for the connections Connecting the multichannel analog inputsAbout Hdmi Selecting the multichannel analog inputsBi-amping your front speakers Other connections Second Zone speaker B setupSwitching the speaker system 2nd Zone setting only.1Large Connecting additional amplifiersBi-wiring your speakers Other connections Multi-room listening Using the multi-room controlsBasic multi-room setup Surround Back System multi-room setupPress Control Connecting an IR receiverMulti-room remote controls Use the Master Volume dial to adjust the volume12V Using this receiver with a Pioneer plasma displayAudio Using the SR+ mode with a Pioneer plasma displayDVD player DVD/LDAssigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuAssigning the Hdmi inputs Other SettingsOther Setup menu Dynamic Range Control SetupVideo Converter Setup Dual Mono SetupLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysVolt Trigger setup Multi-Room and IR receiver setupMaking an audio or a video recording Using other functionsUsing other functions Chapter Reducing the level of an analog signalDisplay shows RESET? Using other functions Using the sleep timerResetting the system Switching the speaker impedanceControlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Programming signals from other remote controlsControlling the rest of your system Erasing one of the remote control button settingsResetting the remote control presets Confirming preset codesProgramming a multi-operation or a shutdown sequence Renaming input source namesDirect function Multi Operation and System Off Using System off Using multi operationsControls for other components Controlling the rest of your system Controls for TVsDecide which component you want to use the remote sensor Operating other Pioneer components with this unit’s sensorAdditional information Chapter TroubleshootingPower Additional informationAdditional information Other audio problemsVideo SettingsDisplay Remote controlSR cable is connected, but XM radio messagesWindows Media Audio 9 Professional Additional information Surround sound formatsDolby About THX THX MusicMode Listening modes with different input signal formatsStereo 2 channel signal formats THX Games ModeAuto Multichannel signal formatsCleaning the unit Additional information SpecificationsDecibel Level Example To establish a safe levelOnce you have established a comfortable sound level Pioneer Corporation
Top Page Image Contents