Intel PCI-X user manual Copper Cabling and Connector Info Fiber Cable Specifications

Page 26

GigMAC-PMC and PCI

 

GigPMC Switch

Board and Driver Users Manual

Step 2 – Remove the CompactPCI or Embedded Mainboard controller from the system, if necessary to access the PMC slot. This will allow the PMC adapter card to be more easily installed. Consult your User's Manual for assistance in opening and removing the mainboard. The PMC card has 3 connectors labeled JN1, JN2 and JN3. JN1 and JN2 are required for all modes of operation while JN3 is required only for 64-bit mode. Your CompactPCI mainboard or other PMC carrier will also contain PMC card connectors labeled JN1 and JN2, and optionally JN3 and JN4. JN4 is for optional user-defined I/O and is only used by the Model 5468 GigPMC switch. Additionally, the mainboard may also contain either a 5 volt or 3.3 volt key to prevent voltage mismatches. Since the PMC card may operate from a 5 or 3.3 volt supply, it can be used in either a 5 or 3.3 volt keyed system. It is very important to align the connectors before pressing the PMC card onto the mainboard to prevent damage to the card or slot.

Step 3 - Align the PMC connectors and the system motherboard Connectors and push down firmly on the PMC card until it is completely seated in the connectors on the mainboard. Once the adapter card has been successfully installed, re-install the mainboard. Re-attach the power cable and any other cables that were removed for the hardware installation procedure.

9.COPPER CABLING AND CONNECTOR INFO

9.1.FIBER CABLE SPECIFICATIONS

Distance (Model 6267-SFP, 5261-LC, 5262-LC, 5262-SC, 5263-SFP multimode/singlemode fiber)

(1000-base-SX 850nm multimode)

(1000-base-LX 1310nm singlemode)

1000BASE-SX/LX (850 nm Laser for multimode-SX, 1310nm laser for single-mode-LX)

Fiber Core Diameter

62.5/125 um 62.5/125 um 50.0/125 um 50.0/125 um 8.0/125 um

Type

 

Fiber

 

Distance

 

Bandwidth

 

 

 

Mhz* km

 

 

 

 

 

 

 

multi-mode

 

160 Mhz * km

 

2 to 220 m

 

 

 

 

 

multi-mode

 

200 Mhz * km

 

2 to 275 m

 

 

 

 

 

multi-mode

 

400 Mhz * km

 

2 to 500 m

 

 

 

 

 

multi-mode

 

500 Mhz * km

 

2 to 550 m

 

 

 

 

 

single-mode

 

500 Mhz * km

 

5-10 km

DSS NETWORKS, INC.

Version: 2.6

Page: 26

Image 26
Contents DSS Networks SeptGigMAC-PMC and PCI GigPMC Switch Environmental Specifications Compatibility IntroductionSee Also PCI-Express models Model NumbersPMC models PCI-X modelsKEY Features Switch Capabilities Models 5468/6468 OEM Developer KIT ContentsGigMAC-PMC and PCI GigPMC Switch System Requirements Wind RiverHardware Information 6.1 Board Photos DSS NETWORKS, INC Transmit and Receive Activity Indicators Board LED IndicatorsLink LNK Indicator Transmit activity Receive activity‰ TBD PMC Connector PIN/SIGNAL Definitions PMC Connectors Pin Assignments Pn1/Jn1 32 Bit PCIPn2/Jn2 32 Bit PCI Pn3/Jn3 32 Bit PCI Pn4/Jn4 optional I/O Model 5468 only PCI Configuration Registers Model Vendor and Device IDSEeprom Listings Model 5262-RJ Default Register Settings GigMAC-PMC and PCI GigPMC Switch Ethernet Frame Latency Power Consumption SpecsHardware Installation Installation in PC Computer Embedded or Compact PCI InstallationCopper Cabling and Connector Info Fiber Cable Specifications Copper RJ-45 Connector and Cable Building the driver Software Driver InstallationLinux Driver Installation and Usage Installing the driver Sample MODULES.CONF File Tuning the Installation ‘Insmod’ Command Line Parameters Parameter Name Valid Default Description Range/SettingsSuggested basic verifications to be run Edit Makefile Un-comment the following define Vxworks Driver Installation and Usage Using dmUtil dpm driver utilityVxWorks usage PCI Registers Show Function MAC Registers Show Function Unit 0, ioAddr 40020000, mac regsMAC Statistics Show Function GigMAC-PMC and PCI GigPMC Switch PHY Registers Show Function Eeprom Show Function MAC Address Show Function Buffer Descriptor Status Show FunctionStarting Frame Generator Stopping Frame GeneratorSwitch Status Show Function DPM Driver Management APIIoctl Command SUB-TYPES Switch Configuration / Management API Functions to reset and initialize switchFunctions to read and write registers in the switch Testing and Verification Specifications Standards Compliance Environmental RangeEnvironmental Standards Compliance pending GigMAC-PMC and PCI GigPMC Switch Environmental Specifications Technical Support and Warranty Warrantee and Support Info
Related manuals
Manual 406 pages 21.68 Kb