Bel Canto Design PRe6 warranty Volume Control

Page 6

Balance Right - (available from the remote only) Shifts balance right in 0.5dB increments and reduces the volume in the opposite channel equally. Balance level is visible on the right side of the display.

MUTE - When coming out of Standby the PRe6 starts in Soft Mute. This volume level can be adjusted in Configuration (of) Inputs. (This Soft mute level is shown as the number of decibels below the current listen- ing level.) Pressing MUTE will first soft mute the unit. The volume quick- ly ramps down to the preset soft mute level and “SOFT” appears on the right side of the display. The vol- ume can be lowered while in soft mute and then taken out of soft mute at the desired listening level. After 3 seconds from pressing MUTE (after the display dims), pressing MUTE again will bring the PRe6 out of Soft mute. Pressing MUTE twice within 3 seconds (before the display dims) will fully mute the unit. The volume quickly ramps down and “MUTE

appears on the right side of the dis- play. The listening level can again be lowered while muted and then taken out of mute at the desired level. Mute shuts off the audio output. Coming out of either mute mode, the volume quickly ramps back up to the dis- played level.

MAIN – Cycles through inputs. On the remote, this is accomplished with the LOOP button

INPUT – On the remote, the input buttons allow you to select between the 1st five active inputs. From the remote, you can cycle through inputs using the LOOP button. From the front panel, you can cycle through inputs by pressing the MAIN button. When switching between inputs, the PRe6 will quickly ramp down the vol- ume, switch inputs, then quickly ramp back up to the programmed volume setting. All inputs can be dis- abled if not used. See CONFIGURA- TION INPUTS section.

PRESS ENTER 4 TIMES OR HOLD FOR 2 SECONDS

VOLUME CONTROL*

SELECT TAPE INPUT*

TO ACCESS INPUT CONFIGURATION MODE

 

 

 

 

 

 

 

 

 

 

SOFT AND FULL MUTE FUNC-

INPUT SELECTION*

HARD MUTES OUTPUT, DISABLES DIS-

TIONS

 

PLAY AND CONTROLS

*ALSO USED FOR NAVIGATION WHEN IN INPUT CONFIGURATION MODE

© 2002 bel canto design, Ltd.

page 6

PRe6 User’s Guide rev082102

Image 6
Contents Users Guide and Warranty Information Multi-Channel Analog Pre-AmplifierMulti-Channel Analog Control Pre-Amplifier Power Connection Unpacking your new PRe6Placement and Initial Setup Design FeaturesFront Panel and Remote Control ConditioningVolume Control Back Panel Configuration PRe6 Setup and Options Factory ConfigurationDefine Inputs DisableSet Main Volume Edit Input NameSpecifications Set Zone 2 volumeSet Soft Mute Offset PRe6 Offset Configuration ConfigurationPRe6 Input Configuration Map Press Enter to Change ConfigurationTape Factory Settings Map Soft Mute OffsetBalanced

PRe6 specifications

Bel Canto Design is renowned for its commitment to high-fidelity audio, and the PRe6 is a testament to this tradition of excellence. As a high-performance preamplifier, the PRe6 seamlessly combines sophisticated technology with elegant design, providing audiophiles with an unparalleled listening experience.

One of the standout features of the PRe6 is its fully balanced architecture, which plays a crucial role in minimizing noise and distortion. This design choice allows the preamplifier to deliver a clean, dynamic sound, ensuring that the fine details of music are presented with clarity and precision. The use of high-quality components, including custom capacitors and discrete resistors, contributes to the overall performance, enhancing both the sonic quality and durability of the unit.

At the heart of the PRe6 lies a versatile digital processing section that is compatible with high-resolution audio formats. This allows users to connect various digital sources, including computers, CD players, and streaming devices, making it an ideal centerpiece for modern audio setups. The PRe6 supports a wide range of digital inputs, including USB, optical, coaxial, and AES/EBU, providing flexibility in connectivity. It can handle PCM resolutions up to 384 kHz and DSD up to 256, ensuring that even the most demanding audiophile will find it meets their needs.

Another notable characteristic of the PRe6 is its intuitive user interface. The elegant front panel features a large display that provides clear feedback on input selection and volume levels. The remote control further enhances usability, giving listeners the ability to adjust settings from across the room.

Additionally, the PRe6 is equipped with advanced features like a programmable volume control, which allows precise adjustments and integration into home automation systems. Its modular design enables easy upgrades, ensuring that the preamplifier can adapt to future advancements in audio technology.

In summary, the Bel Canto Design PRe6 is a high-performing preamplifier that embodies cutting-edge technology and superb craftsmanship. With its balanced architecture, extensive digital connectivity, and user-friendly interface, the PRe6 is poised to satisfy even the most discerning audio enthusiasts. Whether used in a dedicated listening room or a sophisticated home theater setup, the PRe6 delivers exceptional sound quality, ensuring a captivating musical experience.