Intel EMB-945T manual Display

Page 13

Mini - ITX		E M B - 9 4 5 T

Solid Storage Disk	Type II CompactFlash™ slot x 1
Expansion Interface	One PCI slot, One PCI-E(x1), One
	Mini PCI socket
Power Requirement	ATX (+3.3V, +5V, +12V)
Board Size	6.7”(L) x 6.7”(W) (170 mm x 170
	mm)

Operating Temperature 32˚F~ 140˚F (0˚C ~ 60˚C)

Display

Chipset	Intel® 945GM
VGA/LCD Controller	1. Intel® 945GM integrated VGA,
	Share memory up to 224MB with
	DVMT , LCD supports 18/36-bit
	LVDS
	2. Chrontel 7307 for DVI support
	3. Chrontel 7308 for 24/48-bit LVDS
	support
TV-out	Intel® 945GM integrated

Chapter 1 General Information 1- 6

Image 13

Contents Intel Core Duo/Solo Processor Up to 2.0 GHz EMB-945TMini-ITX Marvell 88E8053 Ethernet AC 97 Audio & Mini PCIMini-ITX Copyright NoticeAcknowledgments Packing List Chapter 2 Quick Installation Guide ContentsChapter 1 General Information Chapter 3 Award BIOS Setup Appendix B Programming The Watchdog Timer Driver InstallationChapter Appendix AChapter General InformationChapter 1 General Information 1.1 Introduction Chapter 1 General Information 1.2Features System 1.3 SpecificationsDisplay Page Chapter 2 Quick Installation Guide Quick Installation GuideMini ITX 2.1 Safety Precautions Locating Connectors and Jumpers Component Side 2.2 Location of Connectors and JumpersLocating Connectors and Jumpers Solder Side 2.3Mechanical Drawing Component Side Solder Side 2.4 List of Jumpers Jumpers2.5 List of Connectors ConnectorsCN24 Open 2.6 Setting JumpersClosed 2.8 LVDS2-LCDCN10Voltage Selection JP2 2.7 LVDS1-LCDCN12Voltage Selection JP12.9 COM2 Ring/+5V/+12V Selection JP3 2.10 LCD INVERTER Voltage Selection JP42.14 Digital I/O Connector CN2 2.13 CD-INConnector CN12.12 Clear CMOS JP6 Function2.16 Internal Keyboard Connector CN4 2.15 TV Out Connector CN38 in 8 out2.18 Audio 5.1 Channel / SPDIF Connector CN6 2.17 Fan2 Connector CN52.19 Internal Mouse Connector CN7 2.20 LCD Inverter Connector CN82.21 PCI Express Slot For AAEON CN9 2.23 DVI Connector CN11 2.22 LVDS2-LCDConnector CN102.24 LVDS1-LCDConnector CN12 2.26 COM3 RS-232Serial Port Connector CN14 2.25 COM6 RS-232Serial Port Connector CN132.27 Fan1 ConnectorCN15 Pin Signal2.29 COM4 RS-232Serial Port Connector CN17 2.28 COM5 RS-232Serial Port Connector CN162.30 IrDA Connector CN18 2.32 USB Connector CN20 2.31 ATX Power Connector CN192.33 USB ConnectorCN21 Mini ITXE M B - 9 4 5 T2.34 EIDE Connector CN22 2.36 COM2 RS-232Serial Port Connector 2.35 Front Panel Connector CN23Chapter 3 Award BIOS Setup Award BIOS Setup3.1System Test and Initialization System configuration verificationStandard CMOS Features Entering SetupAdvanced BIOS Features 3.2Award BIOS SetupPower Management Setup Advanced Chipset FeaturesPnP/PCI Configurations Load Fail-SafeDefaultsSave and Exit Setup Set Supervisor/User PasswordExit Without Saving Chapter 4 Driver Installation Driver InstallationFollow the sequence below to install the drivers SetupYukonWin.exe 4.1 InstallationStep 4 - Install Realtek AC97 codec Driver Appendix I/O InformationAppendix A I/O Information A-1 Appendix A I/O Information A-2 A.1 I/O Address MapAppendix A I/O Information A-3 A.2 Memory Address Map A.3 IRQ Mapping ChartAppendix A I/O Information A-4 A.4 DMA Channel AssignmentsAppendix B Programming the Watchdog Time B-1 Programming the Watchdog TimerB.1 Programming Configuring Sequence DescriptionAppendix B Programming the Watchdog Time B-2 2 Modify the Data of the Registers 1 Enter the MB PnP Mode3 Exit the MB PnP Mode Appendix B Programming the Watchdog Timer B-3Configure Control Index=02h WatchDog Timer Configuration RegistersAppendix B Programming the Watchdog Time B-4 Appendix B Programming the Watchdog Timer B-5 B.2 IT8712 Watchdog Timer Initial Program game port enable mov cl, call Set Logic Device CALL Read Configuration Data CMP AL,87h RET Exit Configuration Mode ENDPCALL Read Configuration Data CMP AL,12h Read Configuration Data PROC NEARMOV DX,WORD PTR CS Cfg Port+06h IN AL,DX RET push ax push cx xchg al,cl mov cl,07h END Maincall Superio Set Reg pop cx pop ax ret Set Logic Device endp