Eiki EIP-250, EIP-2600 quick start Turning the Projector On/Off, Turning the Projector on

Page 27

Turning the Projector On/Off

Turning the Projector on

Note that the connections to external equip- ment and power outlet should be done be- fore performing the operations written be- low. (See pages 21 to 24.)

Remove the lens cap and press STANDBY/ON on the projector or ON on the remote control.

•The power indicator illuminates red.

•After the lamp indicator illuminates, the projec- tor is ready to start operation.

Note

•About the Lamp Indicator

The lamp indicator illuminates to indicate the status of the lamp.

Green: The lamp is on.

Blinking in green: The lamp is warming up.

Red: The lamp is shut down abnormally or the lamp should be replaced.

•When switching on the projector, a slight flick- ering of the image may be experienced within the first minute after the lamp has been illumi- nated. This is normal operation as the lamp’s control circuitry is stabilising the lamp output characteristics. It should not be regarded as faulty operation.

•If the projector is put into standby mode and immediately turned on again, the lamp may take some time to start projection.

•When System Lock is set, the keycode input box appears. To cancel the keycode setting, input the keycode that you have already set. See page 46 for details.

Info

•When “Auto Restart” is set to “On”:

If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automati- cally turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. (See page 45.)

•English is the factory default language. If you want to change the on-screen display to an- other language, change the language accord- ing to the procedure on page 44.

Lamp indicator

Power indicator

STANDBY/ON button

STANDBY button

ON button

On-screen display (confirmation message)

Turning the Power off (Putting the Projector into Standby Mode)

Press STANDBY/ON on the projector or STANDBY on the remote control, then press that button again while the confir- mation message is displayed, to put the projector into standby mode.

•The projector cannot be turned on while cool- ing.

Info

•Direct Power Off function:

You can unplug the power cord from the AC out- let even if the cooling fan is still running.

25

Image 27

Contents EIP-2600 EIP-2600 EIP-250Model No Serial No Introduction Esperanza Rancho Santa Margarita, CA 92688-2132 TEL InformationFor Future Reference Maintenance Troubleshooting IndexContents Reference Important Safeguards Damage Requiring Service Avoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Optional accessories AccessoriesProjector Part Names and FunctionsAudio 1 input terminal Rear ViewButton VIDEO, Video buttonsInserting the Batteries Usable Range Quick Start Setup and ProjectionWhen connecting equipment other than a computer, see On the projector On the remote controlControl Upper sideCeiling-mount Setup Setting up the ProjectorSetting up the Projector Standard Setup Front ProjectionProjection PRJ Mode Example Normal Mode Picture Size120 Normal Mode Stretch ModeScreen Size and Projection Distance Is only for EIP-2600 Connecting the Projector to Other EquipmentYou may need other cables or connectors not listed below Example Terminals of EIP-2600Connecting the Projector to Other Equipment Audio OUT Connecting the Power Cord AC socket Power cord To AC outlet suppliedControlling the Projector by a Computer Turning the Projector on Turning the Projector On/OffImage Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Adjusting the Picture SizeAdjusting the Height Use the rear adjustment foot to make the projector levelAdjust lever Make small adjustments Rear adjustment foot Press Keystone Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Correcting Trapezoidal DistortionSwitching the Input Mode Adjusting the VolumeOn-screen display Press Resize Resize ModeAbout Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot FunctionDisplaying an Enlarged Portion of an Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving ImageWhen right-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When left-clickingFollowing shows the items that can be set in the projector Menu ItemsScreen adjustment SCR-ADJ menu ÒHelpÓ menu n Items you can set with the Help menuExample Adjusting ÒBrightÓ Using the Menu ScreenMenu Selections Adjustments Press Qor Oand select Picture to adjustPress Enter To adjust the projected image while watching itPress P or R and select Bright to adjust Press O or Q to adjust the item selectedPicture Adjustment Picture Menu 1Selecting the Picture ModeMenu operation n Adjusting ÒHueÓ, ÒSaturationÓ, or ÒValueÓ Adjusting the ImageAdjusting the Colors Adjusting the Color Temperature7Lamp Setting ProgressiveReducing Image Noise DNR 4Setting the On-screen Display Adjusting the Projected Image SCR ADJ Menu1Setting the Resize Mode 2Adjusting the Image Position 3Keystone CorrectionSelecting the On-screen Display Language Closed Caption Selecting the Setup GuideSelecting the Background Image Reversing/Inverting Projected Images5Setting the Confirmation Sound System Sound 1Auto Sync Auto Sync Adjustment2Auto Power Off Function 4STANDBY ModeSelect System Lock, then press Enter or Q 9Fan Mode Setting7Audio Input EIP-2600 only 0System Lock FunctionLocking the Operation Buttons Keylock FunctionChecking the Lamp Life Status Enter the same keycode in Re- confirmTroubleshooting with the Help Menu Enter button Adjustment buttons P/R/O/Q MENU/HELP buttonUtilizing the Help Menu Functions Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Connecting Pin Assignments Sub 15 pin female connectorDVI-I Terminal 29 pin connector EIP-2600 only USB Terminal Type B USB connector RS-232C Terminal mini DIN 9 pin female connectorBasic format RS-232C Specifications and CommandsComputer control Communication conditionsCommands RS-232C Specifications and CommandsRGB Video Input Picture Mode Standard OK or ERR PAL Computer Computer Compatibility Chart21-24 Troubleshooting49, 50 Specifications Dimensions Index Eiki Industrial Company Limited CanadaDeutschland & Österreich Eastern Europe China Japan & Worldwide