Eiki EIP-250, EIP-2600 quick start Introduction

Page 3
U.S.A. ONLY

Before using the projector, please read this owner’s manual carefully.

Introduction

ENGLISH

1. WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection, modification, or recall that EIKI may be required to give under the 1972 Consumer Product Safety Act,

PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

U.S.A. ONLY

WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light.

WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.

See bottom of projector.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER.

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead sym- bol, within an equilateral triangle, is in- tended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

PRODUCT DISPOSAL

This product utilizes tin-lead solder, and lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or 1-800-242-3454.

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 52.

Authorized representative responsible for the European Union Community Market

EIKI Deutschland GmbH

Am Frauwald 12, 65510 Idstein

E.U. ONLY

1

Image 3
Contents EIP-2600 EIP-2600 EIP-250Model No Serial No Introduction Esperanza Rancho Santa Margarita, CA 92688-2132 TEL InformationFor Future Reference Maintenance Troubleshooting IndexContents Reference Important Safeguards Damage Requiring Service Avoid locations with extremes of temperature Rest your eyes occasionallyDo not block the exhaust and intake vents Using the projector in other countries Temperature monitor functionOther connected equipment Optional accessories AccessoriesProjector Part Names and FunctionsAudio 1 input terminal Rear ViewButton VIDEO, Video buttonsInserting the Batteries Usable Range Quick Start Setup and ProjectionWhen connecting equipment other than a computer, see On the projector On the remote controlControl Upper sideCeiling-mount Setup Setting up the ProjectorSetting up the Projector Standard Setup Front ProjectionProjection PRJ Mode Example Normal Mode Picture Size120 Normal Mode Stretch ModeScreen Size and Projection Distance Is only for EIP-2600 Connecting the Projector to Other EquipmentYou may need other cables or connectors not listed below Example Terminals of EIP-2600Connecting the Projector to Other Equipment Audio OUT Connecting the Power Cord AC socket Power cord To AC outlet suppliedControlling the Projector by a Computer Turning the Projector on Turning the Projector On/OffImage Projection About the Setup GuideAdjusting the Projected Image Adjusting the Focus Adjusting the Picture SizeAdjusting the Height Use the rear adjustment foot to make the projector levelAdjust lever Make small adjustments Rear adjustment foot Press Keystone Press Keystone to enter the Keystone Correction modePress P/Q or O/R to adjust Keystone Correction Correcting Trapezoidal DistortionSwitching the Input Mode Adjusting the VolumeOn-screen display Press Resize Resize ModeAbout Copyrights Switching the Eco+Quiet Mode Operating with the Remote ControlDisplaying and Setting the Break Timer Using the Spot FunctionDisplaying an Enlarged Portion of an Image Auto Sync Auto Sync AdjustmentSelecting the Picture Mode Freezing a Moving ImageWhen right-clicking Using the Remote Control as the Wireless Computer MouseWhen moving the cursor When left-clickingFollowing shows the items that can be set in the projector Menu ItemsScreen adjustment SCR-ADJ menu ÒHelpÓ menu n Items you can set with the Help menuExample Adjusting ÒBrightÓ Using the Menu ScreenMenu Selections Adjustments Press Qor Oand select Picture to adjustPress Enter To adjust the projected image while watching itPress P or R and select Bright to adjust Press O or Q to adjust the item selectedPicture Adjustment Picture Menu 1Selecting the Picture ModeMenu operation n Adjusting ÒHueÓ, ÒSaturationÓ, or ÒValueÓ Adjusting the ImageAdjusting the Colors Adjusting the Color Temperature7Lamp Setting ProgressiveReducing Image Noise DNR 4Setting the On-screen Display Adjusting the Projected Image SCR ADJ Menu1Setting the Resize Mode 2Adjusting the Image Position 3Keystone CorrectionSelecting the On-screen Display Language Closed Caption Selecting the Setup GuideSelecting the Background Image Reversing/Inverting Projected Images5Setting the Confirmation Sound System Sound 1Auto Sync Auto Sync Adjustment2Auto Power Off Function 4STANDBY ModeSelect System Lock, then press Enter or Q 9Fan Mode Setting7Audio Input EIP-2600 only 0System Lock FunctionLocking the Operation Buttons Keylock FunctionChecking the Lamp Life Status Enter the same keycode in Re- confirmTroubleshooting with the Help Menu Enter button Adjustment buttons P/R/O/Q MENU/HELP buttonUtilizing the Help Menu Functions Cleaning the projector MaintenanceTemperature warning indicator Lamp indicator Power indicator Maintenance IndicatorsPlease exercise care when Regarding the Lamp LampReplacing the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Connecting Pin Assignments Sub 15 pin female connectorDVI-I Terminal 29 pin connector EIP-2600 only USB Terminal Type B USB connector RS-232C Terminal mini DIN 9 pin female connectorBasic format RS-232C Specifications and CommandsComputer control Communication conditionsCommands RS-232C Specifications and CommandsRGB Video Input Picture Mode Standard OK or ERR PAL Computer Computer Compatibility Chart21-24 Troubleshooting49, 50 Specifications Dimensions Index Eiki Industrial Company Limited CanadaDeutschland & Österreich Eastern Europe China Japan & Worldwide