Eiki LC-XT3 instruction manual Basic Operation, Turning on / OFF Projector, Turning on Projector

Page 22
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
When Power Management function is ON, projector detects signal interruption and turns off Projection Lamp automatically. Refer to “Power Management” on pages 40 and 41.
When WARNING TEMP. indicator flashes red, projector is automatically turned off. Wait at least 5 minutes, conform READY indicator will light green and projector may be turned on by pressing POWER ON-OFF button.
When both WARNING TEMP. and READY indicators to flash, a projector cannot be turned on by pressing POWER ON-OFF button. In this case, follow procedures below:
1. Turn MAIN ON / OFF SWITCH to OFF.
2. Turn a projector on again. (Refer to steps 2-3 of TURNING ON PROJECTOR on this page.)
When WARNING TEMP. indicator continues to flash, follow procedures below:
1. Turn MAIN ON / OFF SWITCH to OFF and disconnect AC Power Cord from an AC outlet.
2. Check Air Filters for dust accumulation.
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 44.)
4. Turn a projector on again. (Refer to steps 2-3 of TURNING ON PROJECTOR on this page.)
If WARNING TEMP. indicator should still continue to flash, contact sales dealer where you purchased this projector or service center.

BASIC OPERATION

TURNING ON / OFF PROJECTOR

TURNING ON PROJECTOR

1

Complete peripheral connections (with Computer, VCR, etc.)

before turning on projector. (Refer to "CONNECTING TO

 

PROJECTOR" on Pages 12~15 for connecting that equipment.)

2

Connect a projector's AC Power Cord into a wall outlet and turn

MAIN ON / OFF SWITCH to ON. LAMP indicator lights RED,

 

and READY indicator lights GREEN.

3

Press POWER ON-OFF button on Side Control or on Remote

Control Unit to ON. LAMP indicator dims, and Cooling Fans start

to operate. Preparation Display appears on a screen and count- down starts. Signal from source appears after 30 seconds. Current Input position and Lamp status are also displayed on screen for 5 seconds. (Refer to "LAMP MANAGEMENT" on page 45.)

LAMP STATUS

INPUT 1

13

24

30

Preparation Display disappears after 30 seconds.

TURNING OFF PROJECTOR

1

Press POWER ON-OFF button on Side Control or on Remote

Control Unit, and a message "Power off?" appears on a screen.

2

Press POWER ON-OFF button again to turn off projector. LAMP

indicator lights red and READY indicator turns off. After

approximate 90 seconds, READY indicator will light green again and projector may be turned on by pressing POWER ON-OFF button.

Power off?

3

Cooling fans will operate for approximate 2 minutes after projec-

Message disappears after 4 seconds.

tor is turned off. To power down completely, turn MAIN ON/OFF

 

SWITCH to OFF and disconnect AC Power Cord.

22

Image 22
Contents Model LC-XT3 Multimedia ProjectorTo the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design CompatibilityPreparation Name of Each Part of ProjectorConnecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Lens Shift Adjustment Preparation Lens InstallationPositioning Projector Preparation Picture Level and Tilt Adjustment Moving ProjectorReplacement of Terminal Connecting ProjectorTerminals of Projector Audio Input Jacks Connecting Projector INPUT/OUTPUT Terminals and Jacks InputBNC Input Jacks AV Input VIDEO/Y, C JacksSerial Port OUT Terminal Reset ButtonSerial Port Terminal JackConnecting to Computer Terminals ProjectorConnecting to Video Equipment TerminalsBefore Operation Side Controls and IndicatorsSide Controls Lamp Indicator IndicatorsReady Indicator Lamp Replace IndicatorOperation of Remote Control Laser Pointer FunctionZoom Button Volume ButtonWired Remote Jack Focus ButtonOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Turning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorFocus Adjustment Adjusting ScreenZoom Adjustment Keystone AdjustmentBasic Operation Picture Freeze Function Timer FunctionNo Show Function Menu Operation Sound AdjustmentDirect Operation Sound MenuSelecting Computer System Computer InputSelecting Input Source InputAuto Computer Input Automatic MULTI-SCAN SystemSelect Computer System Manually PC System MenuComputer Input Compatible Computer Specifications ResolutionPC Adjust Menu PC AdjustmentAuto PC Adjustment Computer InputComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Level Select Menu Picture Image AdjustmentImage Level Select Direct Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuWhen Select Input 2 5 BNC Terminal Video InputVideo Input Component Video Signal FormatSelecting Video System PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-NCinema Tint Video Input Image Level AdjustmentColor Progressive scanProvides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change code of Remote Control Unit To change code of ProjectorLamp counter reset Wireless Mouse modeProjector mode USBInstallation Operating Wireless MouseMaintenance Operating Wireless MouseAppendix AIR Filter Care and Cleaning Cleaning Projection LensAppendix Lamp Management Yellow Lamp Dim Lamp Red Lamp Mark on LampAppendix Lamp Replacement Front Indicators Rear IndicatorsLamp Handling Precautions Troubleshooting Does not work Remote Control UnitWireless Mouse Function does notTechnical Specifications Appendix Configurations of Terminals DVI-I Terminal DIGITAL/ANALOGSerial Port IN/OUT Terminal Appendix Appendix Appendix Key to better communications Canada

LC-XT3 specifications

The Eiki LC-XT3 is a cutting-edge multimedia projector designed for a wide range of applications, including corporate presentations, educational environments, and home theater setups. This projector embodies a combination of advanced technology and user-friendly features, making it a versatile option for anyone in need of high-quality visual displays.

One of the standout features of the LC-XT3 is its impressive brightness rating of 5,500 ANSI lumens. This level of brightness ensures that images remain clear and vibrant even in well-lit environments, making it an ideal choice for conference rooms or classrooms where ambient light cannot be controlled. The projector also boasts a high contrast ratio of 10,000:1, which delivers deep blacks and vivid colors, enhancing overall image clarity.

It utilizes 3LCD technology, which is well-known for its ability to produce rich, accurate colors and sharp images. This technology works by projecting red, green, and blue light simultaneously, eliminating the rainbow effect often seen in single-chip projectors. This results in smoother, more natural color transitions, making it particularly advantageous for displaying detailed images or videos.

The LC-XT3 supports a range of resolutions, with WUXGA (1920 x 1200) being the native resolution, allowing for the projection of high-definition content. This projector also has the capability to handle 4K input signals, making it future-proof for users who wish to display ultra-high-definition content.

Connectivity is another area where the LC-XT3 excels. It features multiple input options, including HDMI, VGA, and USB ports, making it compatible with various devices, from laptops to streaming devices. This projector also includes a built-in wireless function, allowing for seamless presentations without the need for cumbersome cables.

For added convenience, the LC-XT3 comes equipped with an intuitive, user-friendly interface. It has a built-in speaker that provides adequate sound quality for presentations or small gatherings, while the included remote control allows for easy navigation of settings and features from a distance.

Durability is a key aspect of the Eiki LC-XT3, with a long lamp life of up to 20,000 hours in eco mode, ensuring lower maintenance costs and fewer interruptions during use. This makes it an economical choice for businesses and educational institutions alike.

In summary, the Eiki LC-XT3 is a powerful, versatile projector that meets the needs of various settings with its high brightness, excellent color accuracy, and extensive connectivity options. Its combination of advanced technology and user-friendly design positions it as a leading choice in the multimedia projector market.