Eiki LC-XT3 instruction manual Appendix Lamp Replacement, Front Indicators Rear Indicators

Page 46

APPENDIX

LAMP REPLACEMENT

When the life of the Projection Lamp of this projector draws to an end, the LAMP REPLACE indicator lights yellow. If this indicator lights yellow, replace the projection lamp with a new one promptly.

FRONT INDICATORS

 

REAR INDICATORS

 

 

 

LAMP

READY

WARNING

LAMP TEMP. REPLACE

LAMP

READY

WARNING

TEMP.

LAMP

REPLACE

LAMP REPLACE

INDICATOR

CAUTION

Allow a projector to cool, for at least 45 minutes before

 

For continued safety, replace with a lamp assembly of

you open Lamp Cover. The inside of a projector can

 

the same type.

become very hot.

 

Do not drop a lamp assembly or touch a glass bulb! The

 

 

glass can shatter and may cause injury.

 

 

 

Follow these steps to replace lamp assembly.

1

Check number of lamp to be replaced on Lamp Status Display.

 

2

Turn off a projector and disconnect AC Power Cord. Allow a

projector to cool down for at least 45 minutes.

3

Remove two screws on Lamp Cover and press button to open

 

4

Lamp Cover. (See right figure.)

Loosen two screws and pull out Lamp Assembly to be replaced

 

5

by grasping handle.

Replace Lamp Assembly with a new one and tighten two screws.

 

6

Make sure Lamp is set properly

Replace Lamp Cover and tighten two screws.

 

7

Connect AC Power Cord to a projector and turn a projector on.

 

8

Reset Lamp Replacement Counter. (Refer to section "Lamp

Counter Reset" on page 42.)

NOTE : Do not reset LAMP REPLACEMENT COUNTER when lamp is not replaced.

BUTTON

LAMP

COVER SCREWS

SCREWS

LAMP 3

LAMP 1

LAMP 4

LAMP 2

Make sure which number of lamp needs to be replaced on Lamp Status Display.

Figure shows case of replacing LAMP 2.

CAUTION : DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.

NOTES ON LAMP REPLACEMENT

To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing all 4 lamps at a time.

46

Image 46
Contents Model LC-XT3 Multimedia ProjectorTo the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design CompatibilityPreparation Name of Each Part of ProjectorConnecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Lens Shift Adjustment Preparation Lens InstallationPositioning Projector Preparation Picture Level and Tilt Adjustment Moving ProjectorReplacement of Terminal Connecting ProjectorTerminals of Projector Audio Input Jacks Connecting Projector INPUT/OUTPUT Terminals and Jacks InputBNC Input Jacks AV Input VIDEO/Y, C JacksSerial Port OUT Terminal Reset ButtonSerial Port Terminal JackConnecting to Computer Terminals ProjectorConnecting to Video Equipment TerminalsBefore Operation Side Controls and IndicatorsSide Controls Lamp Indicator IndicatorsReady Indicator Lamp Replace IndicatorOperation of Remote Control Laser Pointer FunctionZoom Button Volume ButtonWired Remote Jack Focus ButtonOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Turning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorFocus Adjustment Adjusting ScreenZoom Adjustment Keystone AdjustmentBasic Operation Picture Freeze Function Timer FunctionNo Show Function Menu Operation Sound AdjustmentDirect Operation Sound MenuSelecting Computer System Computer InputSelecting Input Source InputAuto Computer Input Automatic MULTI-SCAN SystemSelect Computer System Manually PC System MenuComputer Input Compatible Computer Specifications ResolutionPC Adjust Menu PC AdjustmentAuto PC Adjustment Computer InputComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Level Select Menu Picture Image AdjustmentImage Level Select Direct Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuWhen Select Input 2 5 BNC Terminal Video InputVideo Input Component Video Signal FormatSelecting Video System PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-NCinema Tint Video Input Image Level AdjustmentColor Progressive scanProvides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change code of Remote Control Unit To change code of ProjectorLamp counter reset Wireless Mouse modeProjector mode USBInstallation Operating Wireless MouseMaintenance Operating Wireless MouseAppendix AIR Filter Care and Cleaning Cleaning Projection LensAppendix Lamp Management Yellow Lamp Dim Lamp Red Lamp Mark on LampAppendix Lamp Replacement Front Indicators Rear IndicatorsLamp Handling Precautions Troubleshooting Does not work Remote Control UnitWireless Mouse Function does notTechnical Specifications Appendix Configurations of Terminals DVI-I Terminal DIGITAL/ANALOGSerial Port IN/OUT Terminal Appendix Appendix Appendix Key to better communications Canada

LC-XT3 specifications

The Eiki LC-XT3 is a cutting-edge multimedia projector designed for a wide range of applications, including corporate presentations, educational environments, and home theater setups. This projector embodies a combination of advanced technology and user-friendly features, making it a versatile option for anyone in need of high-quality visual displays.

One of the standout features of the LC-XT3 is its impressive brightness rating of 5,500 ANSI lumens. This level of brightness ensures that images remain clear and vibrant even in well-lit environments, making it an ideal choice for conference rooms or classrooms where ambient light cannot be controlled. The projector also boasts a high contrast ratio of 10,000:1, which delivers deep blacks and vivid colors, enhancing overall image clarity.

It utilizes 3LCD technology, which is well-known for its ability to produce rich, accurate colors and sharp images. This technology works by projecting red, green, and blue light simultaneously, eliminating the rainbow effect often seen in single-chip projectors. This results in smoother, more natural color transitions, making it particularly advantageous for displaying detailed images or videos.

The LC-XT3 supports a range of resolutions, with WUXGA (1920 x 1200) being the native resolution, allowing for the projection of high-definition content. This projector also has the capability to handle 4K input signals, making it future-proof for users who wish to display ultra-high-definition content.

Connectivity is another area where the LC-XT3 excels. It features multiple input options, including HDMI, VGA, and USB ports, making it compatible with various devices, from laptops to streaming devices. This projector also includes a built-in wireless function, allowing for seamless presentations without the need for cumbersome cables.

For added convenience, the LC-XT3 comes equipped with an intuitive, user-friendly interface. It has a built-in speaker that provides adequate sound quality for presentations or small gatherings, while the included remote control allows for easy navigation of settings and features from a distance.

Durability is a key aspect of the Eiki LC-XT3, with a long lamp life of up to 20,000 hours in eco mode, ensuring lower maintenance costs and fewer interruptions during use. This makes it an economical choice for businesses and educational institutions alike.

In summary, the Eiki LC-XT3 is a powerful, versatile projector that meets the needs of various settings with its high brightness, excellent color accuracy, and extensive connectivity options. Its combination of advanced technology and user-friendly design positions it as a leading choice in the multimedia projector market.