Eiki LC-HDT10 instruction manual Appendix Lamp Replacement, Front Indicators Rear Indicators

Page 41

APPENDIX

LAMP REPLACEMENT

When the life of the Projection Lamp of this projector draws to an end, the LAMP REPLACE indicator lights yellow. If this indicator lights yellow, replace the projection lamp with a new one promptly.

FRONT INDICATORS

 

REAR INDICATORS

 

 

 

LAMP

READY

WARNING

LAMP TEMP. REPLACE

LAMP

READY

WARNING

TEMP.

LAMP

REPLACE

LAMP REPLACE

INDICATOR

CAUTION

Allow a projector to cool, for at least 45 minutes before

 

For continued safety, replace with a lamp assembly of

you open Lamp Cover. The inside of a projector can

 

the same type.

become very hot.

 

Do not drop a lamp assembly or touch a glass bulb! The

 

 

glass can shatter and may cause injury.

 

 

 

Follow these steps to replace lamp assembly.

BUTTON

1

Check number of lamp to be replaced on Lamp Status Display.

 

2

Turn off a projector and disconnect AC Power Cord. Allow a

projector to cool down for at least 45 minutes.

3

Remove two screws on Lamp Cover and press button to open

 

4

Lamp Cover. (See right figure.)

Loosen two screws and pull out Lamp Assembly to be replaced

 

5

by grasping handle.

Replace Lamp Assembly with a new one and tighten two screws.

 

6

Make sure Lamp is set properly

Replace Lamp Cover and tighten two screws.

 

7

Connect AC Power Cord to a projector and turn a projector on.

 

LAMP

COVER SCREWS

SCREWS

LAMP 3

LAMP 1

LAMP 4

LAMP 2

8

Reset Lamp Replacement Counter. (Refer to section "Lamp

Counter Reset" on page 38.)

NOTE : Do not reset LAMP REPLACEMENT COUNTER when lamp is not replaced.

Make sure which number of lamp needs to be replaced on Lamp Status Display.

Figure shows case of replacing LAMP 2.

CAUTION : DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.

NOTES ON LAMP REPLACEMENT

To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing all 4 lamps at a time.

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Multimedia Projector Model LC-HDT10To the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Computers Features and DesignColor Systems Component VideoName of Each Part of Projector PreparationConnecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe 200 240 V ACPositioning Projector Preparation Lens InstallationLens Shift Adjustment Moving Projector Preparation Picture Level and Tilt AdjustmentTerminals of Projector Connecting ProjectorReplacement of Terminal Input 2 Connecting Projector INPUT/OUTPUT Terminals and Jacks InputSerial Port Terminal Connecting ProjectorTerminals Projector Connecting to ComputerProjector Connecting to Video EquipmentExternal Audio Equipment Audio Amplifier Audio Speaker stereoSide Controls Side Controls and IndicatorsBefore Operation Front Indicators Indicators1WIRED Remote Jack Operation of Remote ControlNumber. Each time you press the Image button, the code is Number of times corresponding to each remote control codeWhile pressing the Menu button, press the Image button Flow of ON-SCREEN Menu Operation HOW to Operate ON-SCREEN MenuOperating ON-SCREEN Menu System BOX Before Operation Menu BARTurning on / OFF Projector Basic OperationTurning on Projector Turning OFF ProjectorNo Show Function Adjusting ScreenPicture Freeze Function Direct Operation Sound AdjustmentMenu Operation Sound MenuPb/Cb, Pr/Cr Selecting Input SourceRGBAnalog RGBScartAutomatic MULTI-SCAN System System SelectAuto System MenuAuto Basic Operation Select Video SystemSystem Select Menu SDI System Select Menu Component videoDisplay Adjustments Display AdjustScreen Adjustments Screen Adjustment DirectAuto PC Adj Display Adjust Auto PC AdjustmentDisplay Adjust Manual Display Adjustments Clamp Current modeImage Adjust Menu Image AdjustmentsImage Level Select Direct Image Level Select MenuDisplay Adjust Image Level Adjustments Progressive scan Noise reductionAuto picture control Auto lamp controlSetting Menu SettingSetting Menu Logo Menu positionCeiling RearPower management To change the code of the Remote Control UnitRemote control To change the code of ProjectorFactory default Lamp counter resetKey lock QuitAIR Filter Care and Cleaning MaintenanceIndicator AppendixMark on Lamp Appendix Lamp ManagementYellow Lamp Dim Lamp Red Lamp Front Indicators Rear Indicators Appendix Lamp ReplacementOrder Replacement Lamp Cleaning Projection LensTroubleshooting Does not work ServiceRemote Control Unit Appendix Indicators and Projector Condition Indicators Projector ConditionInput Appendix Menu TreeImage adjust Technical Specifications Pin Configuration Appendix Configurations of TerminalsResolution Appendix Compatible Computer SpecificationsHDB 15 pin-SCART 21 pin Cable Type No Optional PartsTerminal Board Y/C Type No Terminal Board Faroudja Type NoKey to better communications Canada
Related manuals
Manual 52 pages 16.57 Kb

LC-HDT10 specifications

The Eiki LC-HDT10 is a high-performance laser projector designed to deliver stunning visuals for a variety of applications, including professional presentations, educational environments, and large venues. With its innovative technology and robust features, this projector is an ideal choice for those seeking a reliable projection solution.

One of the standout features of the Eiki LC-HDT10 is its advanced laser light source. This technology provides a bright and vibrant image with a light output of up to 10,000 lumens, making it suitable for both well-lit and dark environments. The laser source also contributes to the projector’s longevity, boasting a lifespan of up to 20,000 hours, significantly reducing the need for frequent lamp replacements and associated maintenance costs.

The LC-HDT10 offers a WUXGA resolution of 1920 x 1200, ensuring that images are sharp, clear, and detailed. This high resolution is particularly beneficial for displaying intricate graphics, detailed charts, and text-heavy presentations. The projector also supports 4K input, providing compatibility with modern devices and enabling high-quality content delivery.

Another key characteristic of the Eiki LC-HDT10 is its extensive connectivity options. It features a range of ports, including HDMI, USB, and 3G-SDI, allowing users to connect various devices seamlessly. This versatility makes it easy to integrate the projector into different setups, whether in a conference room, classroom, or large auditorium.

The projector's advanced display technologies, including 3LCD technology, ensure exceptional color accuracy and brightness uniformity. This translates to more lifelike images and makes the projector an excellent choice for applications where color fidelity is crucial, such as artistic displays or multimedia presentations.

In terms of user convenience, the Eiki LC-HDT10 is designed with ease of use in mind. It includes a built-in web management interface for remote control and monitoring, simplifying projector management in large setups. The projector is also equipped with a lens shift feature, which provides flexibility in installation, allowing for adjustments without distorting the image.

Overall, the Eiki LC-HDT10 is a powerful laser projector packed with advanced features and technologies that elevate the projection experience. Its high brightness, resolution, extensive connectivity options, and ease of use make it a top choice for professionals looking for a versatile and reliable projection solution.
Top Page Image Contents