Eiki LC-HDT10 instruction manual Troubleshooting

Page 43

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check matters below once again.

1.Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING PROJECTOR" on pages 12 ~ 15.

2.Check cable connection. Verify that all computer, video and power cord are properly connected.

3.Verify that all power is switched on.

4.If a projector still does not produce an image, re-start your computer.

5.If an image still does not appear, unplug a projector from your computer and check your computer monitor's display.Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to turn a computer and monitor off before you power up a projector. Power equipment back on in order of : Projector and computer.)

6.If problem still exists, check following chart.

Problem:

Try these Solutions

No power.

Plug a projector into your AC outlet.

 

Turn MAIN ON/OFF switch to ON.

 

Press POWER ON/OFF switch to ON.

 

Make sure READY Indicator lights.

 

Wait 90 seconds after a projector is turned OFF when turning a projector back on.

 

NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as

 

follows:

 

1. LAMP indicator lights bright and READY indicator turns off.

 

2. After 90 seconds, READY indicator lights green again and a projector may be

 

turned on by pressing Power ON-OFF button.

 

Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY

 

indicator flashes, a projector cannot be turned on.

 

(See "TURNING ON/OFF PROJECTOR" section on page 22.)

 

Check Projection Lamp. (Refer to page 41.)

Image is out of

Adjust focus of a projector.

focus.

Check Projection Lens to see if it needs cleaning.

NOTE : Moving a projector from a cool temperature location to a warm temperature location

 

 

may result in moisture condensation on Projection Lens. In such an event, leave a

 

projector OFF and wait until condensation disappears.

Picture is Left/Right

Check Ceiling / Rear feature. (See “SETTING” section on page 36.)

reversed.

 

 

 

Picture is

Check Ceiling feature. (See “SETTING” section on page 36.)

Top/Bottom

 

reversed.

 

 

 

Some displays are

Check Display feature.(See “SETTING” section on page 35.)

not seen during

 

Operation.

 

 

 

No image.

Check connection between your computer or video equipment and a projector.

 

When turning a projector on, it takes about 30 seconds to display an image.

 

Check system that you select is corresponding with your computer or video equipment.

 

Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).

 

 

No sound.

Check audio cable connection from audio input source.

 

Adjust audio source.

 

Press VOLUME (+) button.

 

Press MUTE button.

 

 

43

Image 43
Contents Multimedia Projector Model LC-HDT10To the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Component Video Features and DesignComputers Color SystemsName of Each Part of Projector Preparation200 240 V AC SETTING-UP ProjectorConnecting AC Power Cord For U.S.A. and Canada For Continental EuropeLens Shift Adjustment Preparation Lens InstallationPositioning Projector Moving Projector Preparation Picture Level and Tilt AdjustmentReplacement of Terminal Connecting ProjectorTerminals of Projector Input 2 Connecting Projector INPUT/OUTPUT Terminals and Jacks InputSerial Port Terminal Connecting ProjectorTerminals Projector Connecting to ComputerAudio Amplifier Audio Speaker stereo Connecting to Video EquipmentProjector External Audio EquipmentBefore Operation Side Controls and IndicatorsSide Controls Front Indicators Indicators1WIRED Remote Jack Operation of Remote ControlWhile pressing the Menu button, press the Image button Number of times corresponding to each remote control codeNumber. Each time you press the Image button, the code is Operating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation System BOX Before Operation Menu BARTurning OFF Projector Basic OperationTurning on / OFF Projector Turning on ProjectorPicture Freeze Function Adjusting ScreenNo Show Function Sound Menu Sound AdjustmentDirect Operation Menu OperationRGBScart Selecting Input SourcePb/Cb, Pr/Cr RGBAnalogSystem Menu System SelectAutomatic MULTI-SCAN System AutoSystem Select Menu Component video Basic Operation Select Video SystemAuto System Select Menu SDIScreen Adjustment Direct Display AdjustDisplay Adjustments Screen AdjustmentsAuto PC Adj Display Adjust Auto PC AdjustmentDisplay Adjust Manual Display Adjustments Clamp Current modeImage Level Select Menu Image AdjustmentsImage Adjust Menu Image Level Select DirectDisplay Adjust Image Level Adjustments Auto lamp control Noise reductionProgressive scan Auto picture controlSetting Menu SettingSetting Menu Rear Menu positionLogo CeilingTo change the code of Projector To change the code of the Remote Control UnitPower management Remote controlQuit Lamp counter resetFactory default Key lockAppendix MaintenanceAIR Filter Care and Cleaning IndicatorYellow Lamp Dim Lamp Red Lamp Appendix Lamp ManagementMark on Lamp Front Indicators Rear Indicators Appendix Lamp ReplacementOrder Replacement Lamp Cleaning Projection LensTroubleshooting Remote Control Unit ServiceDoes not work Appendix Indicators and Projector Condition Indicators Projector ConditionInput Appendix Menu TreeImage adjust Technical Specifications Pin Configuration Appendix Configurations of TerminalsResolution Appendix Compatible Computer SpecificationsTerminal Board Faroudja Type No Optional PartsHDB 15 pin-SCART 21 pin Cable Type No Terminal Board Y/C Type NoKey to better communications Canada
Related manuals
Manual 52 pages 16.57 Kb

LC-HDT10 specifications

The Eiki LC-HDT10 is a high-performance laser projector designed to deliver stunning visuals for a variety of applications, including professional presentations, educational environments, and large venues. With its innovative technology and robust features, this projector is an ideal choice for those seeking a reliable projection solution.

One of the standout features of the Eiki LC-HDT10 is its advanced laser light source. This technology provides a bright and vibrant image with a light output of up to 10,000 lumens, making it suitable for both well-lit and dark environments. The laser source also contributes to the projector’s longevity, boasting a lifespan of up to 20,000 hours, significantly reducing the need for frequent lamp replacements and associated maintenance costs.

The LC-HDT10 offers a WUXGA resolution of 1920 x 1200, ensuring that images are sharp, clear, and detailed. This high resolution is particularly beneficial for displaying intricate graphics, detailed charts, and text-heavy presentations. The projector also supports 4K input, providing compatibility with modern devices and enabling high-quality content delivery.

Another key characteristic of the Eiki LC-HDT10 is its extensive connectivity options. It features a range of ports, including HDMI, USB, and 3G-SDI, allowing users to connect various devices seamlessly. This versatility makes it easy to integrate the projector into different setups, whether in a conference room, classroom, or large auditorium.

The projector's advanced display technologies, including 3LCD technology, ensure exceptional color accuracy and brightness uniformity. This translates to more lifelike images and makes the projector an excellent choice for applications where color fidelity is crucial, such as artistic displays or multimedia presentations.

In terms of user convenience, the Eiki LC-HDT10 is designed with ease of use in mind. It includes a built-in web management interface for remote control and monitoring, simplifying projector management in large setups. The projector is also equipped with a lens shift feature, which provides flexibility in installation, allowing for adjustments without distorting the image.

Overall, the Eiki LC-HDT10 is a powerful laser projector packed with advanced features and technologies that elevate the projection experience. Its high brightness, resolution, extensive connectivity options, and ease of use make it a top choice for professionals looking for a versatile and reliable projection solution.