Eiki LC-XB40N owner manual Appendix Indicators and Projector Condition

Page 71

Appendix

Indicators and Projector Condition

Check the indicators for projector condition.

Indicators

 

WARNING

LAMP

Projector Condition

POWER

REPLACE

 

 

red/green

red

yellow

 

 

 

 

 

 

 

 

 

The projector is off. (The AC power cord is unplugged.)

 

 

 

 

 

 

The projector is in stand-by mode. Press the ON/STAND-BY button

 

 

to turn on the projector.

 

 

 

 

 

 

 

 

 

 

 

The projector is operating normally.

 

 

 

 

 

 

 

The temperature inside the projector is abnormally high. The

 

 

 

projector cannot be turned on. When the projector is cooled down

 

 

enough and the temperature returns to normal, the POWER

 

 

 

indicator stops blinking and the projector can be turned on. (The

 

 

 

WARNING indicator keeps blinking.) Check and clean the filter.

 

 

 

 

 

 

 

The projector has been cooled down enough and the temperature

 

 

returns to normal. When turning on the projector, the WARNING

 

 

 

indicator stops blinking. Check and clean the air filter.

 

 

 

 

 

 

 

The projector is preparing for stand-by or the projection lamp is

 

 

being cooled down. The projector cannot be turned on until cooling

 

 

 

is completed and the POWER indicator stops blinking.

 

 

 

 

 

 

 

The projector detects an abnormal condition and cannot be turned

 

 

 

on. Unplug the AC power cord and plug it again to turn on the

 

 

projector. If the projector is turned off again, unplug the AC power

 

 

cord and contact the dealer or the service center for service and

 

 

 

 

 

 

checkup. Do not leave the projector on. It may cause an electric

 

 

 

shock or a fire hazard.

 

 

 

 

 

 

 

The projector is in the Power management mode.

 

 

 

 

 

 

The projector’s Network or Memory viewer function is in an

 

 

abnormal condition.

 

 

 

 

 

 

 

 

 

 

• • • green.

 

• • • red

• • • off

• • • blinks green.

 

• • • blinks red.

 

When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the lamp replacement counter after replacing the lamp. See pages 65–66.

71

Image 71
Contents Memory Viewer Network SupportedPage Compact Design Logo Function Features and DesignTable of Contents Risk of Electric Shock Do not Open To the OwnerVoor de klanten in Nederland Safety InstructionsMoving the Projector Safety Instructions Air CirculationPositioning Precautions Compliance AC Power Cord for the United States and CanadaBottom Part Names and FunctionsFront BackPart Names and Functions Rear Terminal Part Names and Functions Top Control Wired Remote jack Part Names and Functions Remote ControlSpotlight Pointer Part Names and Functions Laser Pointer FunctionPointer Function Remote Control Code Part Names and Functions Wireless Mouse OperationAdjustable Feet Remote Control Operating RangePositioning the Projector InstallationProjector side AC outlet side Installation Connecting the AC Power CordCables used for connection Installation Connecting to a ComputerSee page 75 for ordering optional cables Installation Connecting to Video EquipmentInstallation Connecting to Component Video Equipment PIN Code Input Dialog Box Basic OperationTurning On the Projector Selected Input Source and Lamp ControlBasic Operation Turning Off the Projector On-Screen Menu Basic Operation How to Operate the On-Screen MenuRemote Control Top ControlFor video source Basic Operation Menu BarFor computer source Keystone Correction Basic Operation Zoom and Focus AdjustmentAuto Setup Function Menu Operation Basic Operation Sound AdjustmentDirect Operation COMPUTER/VIDEO/NETWORK button Basic Operation Remote Control OperationNo Show button Basic OperationTop Control Computer InputInput Source Selection RGB Computer 1 Analog/Computer Input Source Selection RGB PC digital, RGB AV Hdcp Computer InputPC System Menu Computer Input Computer System SelectionSelecting Computer System Manually Auto PC Adj Computer Input Auto PC AdjustmentPC Adjust Menu To store adjustment parametersComputer Input Manual PC Adjustment To store adjusted data To clear adjusted data parametersComputer Input Image Mode Selection Computer Input Image Adjustment Wide Screen Size AdjustmentNormal TrueDigital zoom CustomDigital zoom + Auto Top Control Remote ControlVideo Input Input Source Selection Video, S-videoSource Select Menu Component RGB ScartAV System Menu Video or S-Video Video Input Video System SelectionVideo or S-Video ComponentImage1-4 Video Input Image Mode SelectionCinema Tint Video Input Image AdjustmentColor Progressive Video InputNoise reduction Custom Screen Menu Video Input Screen Size AdjustmentAuto setup SettingSetting Display KeystoneBlue back Capture Logo Logo and Logo PIN code lock settingsLogo select Capture Logo selectLogo PIN code lock Change the Logo PIN code lock settingEnter a Logo PIN code Change the Logo PIN codeInput search Ceiling Rear CeilingRear Power management Power managementStandby mode Pointer PIN code lock Security Key lock, PIN code lock, Alarm settingsKey lock Key lockChange the PIN code Change the PIN code lock settingAlarm Enter a PIN codeLamp counter FanFan Fan controlFilter counter Factory defaultFactory default Filter counterRelease the alarm setting Antitheft Alarm FunctionHow to Use the Antitheft Alarm Function Set the alarmChange the PIN code Antitheft Alarm FunctionRear Terminal Reset the settings Alarm operating configurationCharge the built-in batteries Safety Precautions for Ni-MH Battery Pack Then check the matters below Maintenance and CleaningResetting the Filter Counter Maintenance and Cleaning Cleaning the FilterCleaning the Projector Cabinet Maintenance and Cleaning Slide ShutterCleaning the Projection Lens Service Parts No 331 Maintenance and Cleaning Lamp ReplacementReset the lamp counter Maintenance and Cleaning Resetting the Lamp Counter Lamp Handling PrecautionsAppendix TroubleshootingPIN code dialog box appears at start-up AppendixSound Appendix Menu TreeComputer Input/Video Input Setting Video Input SettingProjector Condition Appendix Indicators and Projector ConditionON-SCREEN Resolution Appendix Compatible Computer Specifications31.47 59.94 Appendix Technical Specifications Optional Parts AccessoriesAppendix PJ Link Notice Terminal Analog RGB Mini D-sub 15 pin Appendix Configurations of TerminalsUSB Connector Series a USB Connector Series BAppendix PIN Code Number Memo Alarm PIN Code NoKey to better communications Canada

LC-XB40N specifications

The Eiki LC-XB40N is a high-performance projector designed for a variety of applications, including corporate presentations, educational settings, and larger venues. This robust device excels in delivering vivid and crisp images, making it a preferred choice for professionals seeking quality projection solutions.

At the heart of the Eiki LC-XB40N is its impressive brightness level, which typically exceeds 4,000 ANSI lumens. This high lumen output ensures that images remain sharp and bright even in well-lit environments, allowing for effective presentations without the need to dim the lights. The projector features a native XGA resolution of 1024 x 768 pixels, which is standard for most business applications, supporting a clear and detailed visual experience.

One of the standout technologies in the Eiki LC-XB40N is its advanced 3LCD projection system. This technology enhances color accuracy and consistency, reducing the risk of color distortions that can occur in other projection methods. The result is vibrant colors and realistic images, which are particularly beneficial for multimedia presentations that involve photographs or video content.

In addition to its impressive visuals, the Eiki LC-XB40N is built for convenience and flexibility. It offers a range of connectivity options, including HDMI, VGA, and composite inputs, allowing it to connect seamlessly with various devices such as laptops, desktops, and DVD players. The HDMI interface, in particular, supports high-definition content, which is essential for modern presentations.

The projector also incorporates a long lamp life, often rated at up to 5,000 hours in eco mode. This reduces the frequency of lamp replacements and lowers overall maintenance costs, making it a cost-effective choice for organizations. Furthermore, the Eiki LC-XB40N features a comprehensive set of image adjustment tools, including keystone correction and lens shift capabilities, ensuring that images are perfectly aligned and projectors can be set up in diverse environments.

Overall, the Eiki LC-XB40N stands out with its powerful performance, advanced projection technologies, and user-friendly features, making it a reliable option for anyone in need of a high-quality projection solution for professional settings. Its combination of brightness, color accuracy, and flexible connectivity ensures that it meets the needs of today’s dynamic presentation environments.