Eiki LC-XB23 owner manual Indicators and Projector Condition

Page 58

Appendix

Indicators and Projector Condition

Check the indicators for projector condition.

Indicators

 

 

 

WARNING

LAMP

Projector Condition

 

POWER

REPLACE

 

 

red/green

red

yellow

 

 

 

 

 

 

 

 

 

 

 

 

The projector is off. (The AC power cord is unplugged.)

 

 

 

 

 

 

 

 

 

 

 

The projector is preparing for stand-by or the projection lamp is

 

 

 

 

 

 

 

 

 

being cooled down. The projector cannot be turned on until cooling

 

 

 

 

 

is completed.

 

 

 

 

The projector is ready to be turned on with the POWER ON-OFF

 

 

 

 

 

 

 

 

button.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The projector is operating normally.

 

 

 

 

 

 

 

 

 

 

The projector is in the Power management mode.

 

 

 

 

 

 

 

 

 

 

 

The temperature inside the projector is abnormally high. The

 

 

 

 

 

projector cannot be turned on. When the projector is cooled down

 

 

 

 

enough and the temperature returns to normal, the POWER

 

 

 

 

 

indicator emits a red light and the projector can be turned on. (The

 

 

 

 

 

WARNING indicator keeps blinking.) Check and clean the air filters.

The projector has been cooled down enough and the temperature

returns to normal. When turning on the projector, the WARNING indicator stops blinking. Check and clean the air filters.

The projector detects an abnormal condition and cannot be turned on. Unplug the AC power cord and plug it again to turn on the projector. If the projector is turned off again, disconnect the AC

power cord and contact the dealer or the service center for service and checkup. Do not leave the projector on. It may cause an electric shock or a fire hazard.

• • • green.

• • • red

• • • off

• • • blinks green.

• • • blinks red.

 

When the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the lamp replacement counter after replacement of the lamp. See page 52 and 53.

58

Image 58
Contents Model LC-XB23 Features and Design Compact Design Multilanguage Menu DisplayTable of Contents To the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandAir Circulation Installing the Projector in Proper PositionMoving the Projector Compliance Federal Communication Commission NoticeFront Part Names and FunctionsBack Bottom Rear Terminal Top Control Remote Control Point ed 78 Volume + / buttonsRemote Control Battery Installation Operating RangeAdjustable Feet InstallationPositioning the Projector Installation Connecting the AC Power Cord Connecting to a Computer Cables used for connectionConnecting to Video Equipment Connecting to Component Video Equipment Turning On the Projector Selected Input Source and Lamp ModeBasic Operation PIN Code Input Dialog BoxTurning Off the Projector Top Control How to Operate the On-Screen MenuRemote Control On-Screen MenuMenu Bar PC System MenuZoom and Focus Adjustment Keystone CorrectionSound Adjustment Remote Control OperationKeystone button Input Menu Computer InputInput Source Selection Source Select MenuComputer System Selection Selecting Computer System ManuallyPC Adjust Menu Auto PC AdjustmentTo store adjustment parameters Menu Operation Auto PC AdjManual PC Adjustment To clear adjusted data ResetMode free To store adjusted dataImage Level Selection Image Level Adjustment Screen Size Adjustment Digital zoom + Digital zoomVideo Input Input Source Selection Video, S-VideoComponent Input Source Selection Component, RGB Scart 21-pinRGB Scart Component Auto Video System SelectionVideo or S-Video Auto AV System Menu Video or S-VideoCinema Image1~4Color TintNoise reduction ProgressiveProvide the image at a normal video aspect ratio of 4 Setting SettingLogo select Logo Logo and Logo PIN code lock settingsCapture Logo PIN code lock Logo PIN code lock Dialog BoxRear Power managementCeiling TerminalLamp control To change the code for the remote controlOn start To change the code for the projectorKey lock Security Key lock and PIN code lock settingsPIN code lock Enter a PIN code Change the PIN code lock settingChange the PIN code Factory default Lamp counterMaintenance and Cleaning Then check the matters belowCleaning the Air Filters Attaching the Lens CoverCleaning the Projection Lens Cleaning the Projector CabinetReset the lamp replacement counter Lamp ReplacementService Parts No 323 Lamp Replacement Counter When the Lamp replacementTroubleshooting AppendixAppendix Menu Tree Computer Input / Video InputVideo Input Setting Indicators and Projector Condition Projector ConditionCompatible Computer Specifications ON-SCREEN ResolutionTechnical Specifications Accessories Optional PartsTerminal Analog RGB Mini D-sub 15 pin Configurations of TerminalsUSB Connector Series B Terminal Mini DIN 8-PINPIN Code Number Memo Logo PIN Code Lock NoKey to better communications Canada