Eiki LC-X5 instruction manual Appendix Lamp Replacement, Figure shows case of replacing Lamp

Page 45

APPENDIX

LAMP REPLACEMENT

When the life of the Projection Lamp of this projector draws to an end, the LAMP REPLACE indicator lights yellow. If this indicator lights yellow, replace the projection lamp with a new one promptly.

LAMP REPLACE

INDICATOR




							CAUTION


	Allow a projector to cool, for at least 45 minutes before				For continued safety, replace with a lamp assembly of
	you open Lamp Cover. The inside of a projector can				the same type.
	become very hot.				Do not drop a lamp assembly or touch a glass bulb! The
					glass can shatter and may cause injury.

Follow these steps to replace lamp assembly.

	1	Check number of lamp to be replaced on Lamp Status
		Check number of lamp to be replaced on Lamp Status
	2	Display.
	2	Turn off a projector and disconnect AC Power Cord. Allow a
		Turn off a projector and disconnect AC Power Cord. Allow a
		projector to cool for at least 45 minutes.
	3	Loosen 3 screws on Lamp Cover and remove Lamp Cover.
	3	(See right figure.)
		(See right figure.)
	4	Loosen 2 screws and pull out Lamp Assembly to be replaced
	4	by grasping handle.
	5	Replace Lamp Assembly with a new one and tighten 2 screws.
	5	Make sure that Lamp Assembly is set properly
	6	Make sure that Lamp Assembly is set properly
	6	Replace Lamp Cover and tighten 3 screws.
		Replace Lamp Cover and tighten 3 screws.
	7	Connect AC Power Cord to a projector and turn projector on.
	7
	8	Reset Lamp Replacement Counter. (Refer to section "Lamp
	8	Counter Reset" on page 41.)

NOTE : Do not reset LAMP REPLACEMENT COUNTER when lamp is not replaced.

SCREWS

LAMP

COVER

LAMP 1

LAMP 2

SCREWS

Make sure which number of lamp needs to be replaced on Lamp Status Display.

Figure shows case of replacing LAMP 2.

CAUTION : DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.

NOTES ON LAMP REPLACEMENT

To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing all 2 lamps at a time.

45

Image 45

Contents Multimedia Projector LC-X5L LenslessTo the Owner Voor de klanten in Nederland Safety InstructionsFederal Communication Commission Notice CompliancesTable of Contents Compatibility Features and DesignName of Each Part of Projector PreparationSETTING-UP Projector Connecting AC Power CordFor U.S.A. and Canada For Continental Europe Preparation Lens Installation Lens Shift AdjustmentPositioning Projector Moving Projector Preparation Picture Level and Tilt AdjustmentConnecting Projector Replacement of TerminalTerminals of Projector Input 1, 2 Connecting Projector INPUT/OUTPUT Terminals and Jacks InputAudio Output Jacks Terminals Projector Connecting to Computer2INPUT Terminals of a Projector Connecting to Video EquipmentBefore Operation TOP Controls and IndicatorsLaser Pointer Function Operation of Remote ControlRemote Control Batteries Installation HOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Screen Menu Before Operation Menu BARTurning on / OFF Projector Basic OperationTurning on Projector Turning OFF ProjectorAdjusting Screen Focus AdjustmentKeystone Adjustment Timer Function Basic Operation Picture Freeze FunctionNo Show Function Direct Operation Sound AdjustmentMenu Operation Sound MenuSelecting Input Source Computer InputSelecting Computer System InputSelect Computer System Manually Computer Input Automatic MULTI-SCAN SystemAuto PC System MenuResolution Computer Input Compatible Computer SpecificationsAuto PC Adjustment PC AdjustmentPC Adjust Menu Computer InputComputer Input Manual PC Adjustment Display area Display area HFull screen Image Level Select Direct Picture Image AdjustmentImage Level Select Menu Image Select MenuImage Adjust Menu Computer Input Image Level AdjustmentScreen Menu Picture Screen AdjustmentVideo Input When Select Input 2 5 BNC TerminalVideo Input Selecting Video SystemAuto AV System Menu Video or S-VIDEOCinema Color Video Input Image Level AdjustmentTint Progressive scanProvides image at a normal video aspect ratio of 4 Setting Setting MenuSetting Menu To change code of Projector To change code of Remote Control UnitWireless Mouse mode Projector modeLamp counter reset Maintenance Operating Wireless MouseInstallation Operating Wireless MouseCleaning Projection Lens Appendix AIR Filter Care and CleaningYellow Lamp Dim Lamp Red Lamp Mark on Lamp Appendix Lamp ManagementFigure shows case of replacing Lamp Appendix Lamp ReplacementLamp Handling Precautions Troubleshooting Wireless Mouse Remote Control UnitDoes not work Function does notTechnical Specifications DVI-I Terminal DIGITAL/ANALOG Appendix Configurations of TerminalsUSB Port Terminal Key to better communications Canada