Eiki LC-UXT1 instruction manual Appendix Lamp Replacement, Order Replacement Lamp

Page 46

APPENDIX

LAMP REPLACEMENT

CAUTION

For continued safety, replace with a lamp assembly of same type.

Allow a projector to cool for at least 45 minutes before you open Lamp Cover. Inside of a projector can become very hot.

CAUTION

Do not drop a lamp assembly or touch a glass bulb! Glass can shatter and may cause injury.

Follow these steps to replace lamp assembly.

1

Check number of lamp to be replaced on Lamp Status Display.

 

2

Turn off a projector and disconnect AC Power Cord. Allow a

projector to cool down for at least 45 minutes.

3

Remove two screws on Lamp Cover and press button to open

 

4

Lamp Cover. (See right figure.)

Loosen two screws and pull out Lamp Assembly to be replaced

 

 

by grasping handle.

BUTTON

LAMP

COVER SCREWS

SCREWS

5

Replace Lamp Assembly with a new one and tighten two screws.

 

6

Make sure Lamp is set properly

Replace Lamp Cover and tighten two screws.

 

7

Connect AC Power Cord to a projector and turn a projector on.

 

8

Reset Lamp Replacement Counter. (Refer to section "Lamp

 

 

Counter Reset" on page 42.)

NOTE : Do not reset LAMP REPLACEMENT COUNTER when lamp is not replaced.

LAMP 3

LAMP 1

LAMP 4

LAMP 2

Make sure which number of lamp needs to be replaced on Lamp Status Display.

Figure shows case of replacing LAMP 2.

CAUTION : DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.

NOTES ON LAMP REPLACEMENT

To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing all 2 lamps at a time.

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through your dealer. When ordering Projection Lamp, give following information to dealer.

Model No. of your projector : PLC-UXT1

Replacement Lamp Type No. : POA-LMP42

(Service Parts No. 610 292 4831)

46

Image 46
Contents Model LC-UXT1 Multimedia ProjectorTo the Owner Risk of Electric Shock Do not OpenSafety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design CompatibilityPreparation Name of Each Part of ProjectorConnecting AC Power Cord SETTING-UP ProjectorFor U.S.A. and Canada For Continental Europe Lens Shift Adjustment Preparation Lens InstallationPositioning Projector Preparation Picture Level and Tilt Adjustment Moving ProjectorReplacement of Terminal Connecting ProjectorTerminals of Projector Audio Input Jacks Connecting Projector INPUT/OUTPUT Terminals and Jacks InputBNC Input Jacks AV Input VIDEO/Y, C JacksSerial Port OUT Terminal Reset ButtonSerial Port Terminal JackConnecting to Computer Terminals ProjectorConnecting to Video Equipment TerminalsBefore Operation Side Controls and IndicatorsSide Controls Lamp Indicator IndicatorsReady Indicator Lamp Replace IndicatorOperation of Remote Control Laser Pointer FunctionZoom Button Volume ButtonWired Remote Jack Focus ButtonOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Turning on Projector Basic OperationTurning on / OFF Projector Turning OFF ProjectorFocus Adjustment Adjusting ScreenZoom Adjustment Keystone AdjustmentBasic Operation Picture Freeze Function Timer FunctionNo Show Function Menu Operation Sound AdjustmentDirect Operation Sound MenuSelecting Computer System Computer InputSelecting Input Source InputAuto Computer Input Automatic MULTI-SCAN SystemSelect Computer System Manually PC System MenuComputer Input Compatible Computer Specifications ResolutionPC Adjust Menu PC AdjustmentAuto PC Adjustment Computer InputComputer Input Manual PC Adjustment Display area H Display areaFull screen Image Level Select Menu Picture Image AdjustmentImage Level Select Direct Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuWhen Select Input 2 5 BNC Slot Video InputVideo Input Component Video Signal FormatSelecting Video System PAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-NCinema Tint Video Input Image Level AdjustmentColor Noise reductionProvides image at a normal video aspect ratio of 4 Setting Menu SettingSetting Menu To change code of Remote Control Unit To change code of ProjectorLamp counter reset Wireless Mouse modeProjector mode USBInstallation Operating Wireless MouseMaintenance Operating Wireless MouseAppendix AIR Filter Care and Cleaning Cleaning Projection LensAppendix Lamp Management Yellow Lamp Dim Lamp Red Lamp Mark on LampAppendix Lamp Replacement Order Replacement LampTroubleshooting Does not work Remote Control UnitWireless Mouse Function does notTechnical Specifications Appendix Configurations of Terminals DVI-I Terminal DIGITAL/ANALOGSerial Port IN/OUT Terminal Key to better communications Canada