Intel TPC-1070 user manual RS422-MASTER

Page 53

1 5

6 9

Note:

indicates the switch jumper

S4

S5

0 9 8 7 6 5 4 3 2 1

2 1

RS232

ON

ON

S4

S5

0 9 8 7 6 5 4 3 2 1

2 1

RS485

ON

ON

S4

S5

0 9 8 7 6 5 4 3 2 1

2 1

RS422-MASTER

ON

ON

S4

S5

0 9 8 7 6 5 4 3 2 1

2 1

RS422-SLAVE

ON

ON

PIN

RS-232

RS-422

RS-485

1

NDCD

TX-

D-

2

NRX

TX+

D+

3

NTX

RX+

4

NDTR

RX-

5

GND

6

NDSR

7

NRTS

8

NCTS

9

NRI

41

AppendixA

Image 53

Contents TPC-1070 Copyright Acknowledgements Product Warranty 2 years FCC Class a Technical Support and Assistance Declaration of ConformitySafety Instructions Wichtige Sicherheishinweise Vii Viii Contents Appendix Serial Port Settings Appendix G Xii General Information Introduction SpecificationsRJ-45 Ethernet port SafetyCompact Flash Slot TypeII PCI-104 EnvironmentLCD Specifications Power Touchscreen SpecificationsI/O port arrangement I/O Port ArrangementPanel Mounting Panel MountingDimensions Dimensions & CutoutSystem Setup Install CompactFlash memory card Power receptor and button pin assignments Touchscreen Calibration System Engine Main Board Connector Main Board Connector and Jumper Setting ListSoftware Configuration Path \TPC-1070H\Driver\LAN\ Available for the OS’s below Utilities & DriversPath \TPC-1070H\Driver\VGA\ Available for the OS’s below Advantech COM Driver Advantech COM Driver Installation Click Next to continue installation Click uninstall icon to remove ?PCI Serial Port Page Found New Hardware and Click Next to continue installation Click Finish the Advantech PCI Serial Port to continue Page Found New Hardware and Click Next to continue installation Watchdog Timer WDT Driver Installation Installing the TPC-1070 Watchdog Timer Driver Click Next to proceed Page Page Page How to Use the TPC-1070 Watchdog Timer Page Page Windows XP Embedded Horm EWFVersion Information Advantech UtilitiesOSLock and OSUnLock Serial Port Settings COM4 Setting Appendix a Serial Port SettingsCOM1/ COM3 Connector Definition RS422-MASTER Page Watchdog Timer on WinCE DeviceIOControl Appendix B Watchdog Timer on WinCEAppendixB Ioctl Wdtenable How to Use the Control CodeIoctlwdtgettimeout Examples CTLCODEFILEDEVICEUNKNOWN,ID, METHODBUFFERED, FileanyaccessAppendixB Page Watchdog Timer Programming Overview Appendix C Watchdog Timer ProgrammingFigure C.1 Watchdog timer programming procedure Watchdog Timer ProgrammingTable C.1 Watchdog Timer Registers Example Programs Enable watchdog timer and set 10 sec. as timeout intervalEnable watchdog timer and set 5 minutes as timeout interval Enable watchdog timer to be reset by mouse Enable watchdog timer to be reset by keyboard Generate a time-out signal without timer counting Page Accessory Kit Assembly CompactFlash to IDE Transfer Kit Appendix D Accessory Kit AssemblyFigure D.3 CompactFlash Slot Figure D.6 Connect the CD-ROM via the IDE Cable USB Driver Installation NoticeHDD Kit Assembly Figure E.1 Removing the Rear HDD Cover Appendix E HDD Kit AssemblyTouchscreen Installation Configuration Driver Installation Appendix F Touchscreen Installation & ConfigurationFigure F.3 Install License Agreement Figure F.5 Uninstall Uninstall the DriverCalibrate Touchscreen CalibrationFigure F.8 Standard Calibration Figure F.10 Standard Calibration Figure F.11 Advanced Calibration Draw Figure F.13 Plot Calibration DataFigure F.14 Draw Figure F.16 Option OptionPage Fuse Specifications Fuse Replacement Appendix G Fuse SpecificationsFuse Specifications