Intel IM-Q35 Series Bios Setup Suspend mode, USB Device Wakeup from S3/S4, Acpi Version Features

Page 50
The S1 sleep mode is a low power state. In this state, no system context is lost (CPU or chipset) and hard- ware maintains all system context.
The S3 sleep mode is a lower power state where the information of system configuration and open appli- cations/files is saved to main memory that remains powered while most other hardware components turn off to save energy. The information stored in memory will be used to restore the system when a “wake up” event occurs.

BIOS Setup

Suspend mode

This item specifies the power saving modes for ACPI function. If your operating system supports ACPI, you can choose to enter the Standby mode in S1 (POS) or S3 (STR) fashion through the setting of this field. Options are:

[S1 (POS)]

[S3 (STR)]

USB Device Wakeup from S3/S4

This setting allows the activity of the USB device to wake up the system from S3/S4 sleep state.

ACPI Version Features

This setting allows you to select the ACPI version.

APM Configuration

Resume On PME#

When setting to [Enabled], this setting allows your system to be awakened from the power saving modes through any event on PME (Power Management Event).

Resume On RTC Alarm

When [Enabled], your can set the date and time at which the RTC (real-time clock) alarm awakens the system from suspend mode.

Restore On AC Power Loss

This item specifies whether your system will reboot after a power failure or interrupt occurs. Settings are:

[Power Off]

Always leaves the computer in the power off state.

[Power On]

Always leaves the computer in the power on state.

[Last State]

Restores the system to the status before power failure

 

or interrupt occurred.

3-11

Image 50
Contents IM-Q35 Series MS-9820 V1.X MainboardRevision History Copyright NoticeTrademarks Technical SupportSafety Instructions Micro-Star International MS-9820 FCC-B Radio Frequency Interference StatementWeee Waste Electrical and Electronic Equipment Statement Page Vii Contents Page Product Overview IDE Mainboard SpecificationsLAN SataMounting SlotsForm Factor Block Diagram Mainboard Layout IM-Q35 Mainboard Mini ITXBoard Dimension Back Panel & I/O Shield Drawing Power Consumption ConditionSafety Compliance & Mtbf RFIPage Hardware Setup Quick Components Guide CPU Central Processing Unit Introduction to LGA 775 CPUCPU & Cooler Installation Lift the load lever up and open the load plate Locking switch DDR2 Dual-Channel mode Population RuleMemory Installing Memory Modules Volt NotchATX 12V Power Connector JPW1 Power SupplyATX 20-Pin System Power Connector JPWR1 JPW1Back Panel RS-232 PortHardware Setup USB Port Audio PortsIDE2 ConnectorsIDE Connector IDE2 Serial ATA Connector SATA1 ~ SATA4 SATA4 SATA1 SATA3 SATA2CPUFAN1SYSFAN1 Fan Power Connectors CPUFAN1, SYSFAN1Front Panel Connector JFP1 JFP1JAUD1 Front Panel Audio Connector JAUD1RS-232 Port Connector Jcom JCOM1USB 2.0 Bracket Front USB Connector JUSB1 ~JUSB1 JUSB2 PDIF-Out Connector JSPD1 Optional, for Hdmi ADD2 card only Audio Amplifier Connector JAMP1Chassis Intrusion Connector JCI1 JBAT1 JumperClear Cmos Jumper JBAT1 Slots PCI Peripheral Component Interconnect Express SlotPage Bios Setup Entering Setup Press Del to enter SetupGeneral Help F1 Control KeysGetting Help Main MenuMenu Bar System Time AMI BIOS, Processor, System MemoryMain System DateCPU Configuration AdvancedPeci Primary/Secondary/Third/Fourth/Fifth IDE Master/Slave IM-Q35 Mainboard IDE Configuration SATA#1 ConfigurationConfigure SATA#1 as Watch Dog Super IO Configuration Serial Port 1 / 2 AddressSerial Port2 Mode Chassis IntrusionCPU/System Smart FAN Target CPU/Systen Smart FAN ModeAcpi Configuration CPU/System Smart Fan ToleranceAPM Configuration Resume On PME# Bios Setup Suspend modeAcpi Version Features Resume On RTC AlarmSerial Port Mode IM-Q35 Mainboard Intel AMT Configuration Intel AMT SupportRemote Access Configuration Redirection After Bios PostUSB Configuration Legacy USB Support Bios Setup Terminal TypeSredir Memory Display Delay USB 2.0 Controller ModeTPM Enable/Disable Status IM-Q35 Mainboard USB Mass Storage Reset DelayExcute TPM Command Emulation TypeBootup Num-Lock BootBoot Settings Configuration Quick Boot Wait For ‘F1’ If ErrorIM-Q35 Mainboard Boot Device Priority 1st Boot Device Removable Drives 1st DriveSecurity Supervisor Password / Change Supervisor PasswordUser Password / Change User Password Dvmt Mode Select North Bridge Configuration Initate Graphics AdapterInternal Graphics Mode Select ChipsetGbE LAN Boot Bios Setup DVMT/FIXED MemorySouth Bridge Chipset Configuration USB Functions USB 2.0 ControllerME-KT ME-HECIME-IDER Exit Page System Resources Watch Dog Timer Setting Software code Sioidx equ 4EH SIODTAequ 4FHBootblock Initialization Code Checkpoints AMI Post CodeIM-Q35 Mainboard Bootblock Recovery Code Checkpoints CdromPost Code Checkpoints Initializes Dmac -1 & DMAC-2 Resource List PCI Device