Intel IM-Q35 Series manual IM-Q35 Mainboard Boot Device Priority 1st Boot Device

Page 55

IM-Q35 Mainboard

Boot Device Priority

1st Boot Device

The items allow you to set the sequence of boot devices where BIOS attempts to load the disk operating system. First press <Enter> to enter the sub-menu. Then you may use the arrow keys to select the desired device, then press <+>, <-> or <PageUp>, <PageDown> key to move it up/down in the priority list.

Removable Drives

1st Drive

This setting allows users to set the priority of the removable devices. First press <Enter> to enter the sub-menu. Then you may use the arrow keys ( -¯ ) to select the desired device, then press <+>, <-> or <PageUp>, <PageDown> key to move it up/down in the priority list.

3-16

Image 55

Contents MS-9820 V1.X Mainboard IM-Q35 SeriesTechnical Support Copyright NoticeTrademarks Revision HistorySafety Instructions FCC-B Radio Frequency Interference Statement Micro-Star International MS-9820Weee Waste Electrical and Electronic Equipment Statement Page Vii Contents Page Product Overview Sata Mainboard SpecificationsLAN IDEForm Factor SlotsMounting Block Diagram IM-Q35 Mainboard Mini ITX Mainboard LayoutBoard Dimension Back Panel & I/O Shield Drawing Condition Power ConsumptionRFI Safety Compliance & MtbfPage Hardware Setup Quick Components Guide Introduction to LGA 775 CPU CPU Central Processing UnitCPU & Cooler Installation Lift the load lever up and open the load plate Locking switch Memory Dual-Channel mode Population RuleDDR2 Volt Notch Installing Memory ModulesJPW1 Power SupplyATX 20-Pin System Power Connector JPWR1 ATX 12V Power Connector JPW1RS-232 Port Back PanelAudio Ports Hardware Setup USB PortIDE Connector IDE2 ConnectorsIDE2 SATA4 SATA1 SATA3 SATA2 Serial ATA Connector SATA1 ~ SATA4JFP1 Fan Power Connectors CPUFAN1, SYSFAN1Front Panel Connector JFP1 CPUFAN1SYSFAN1JCOM1 Front Panel Audio Connector JAUD1RS-232 Port Connector Jcom JAUD1JUSB1 JUSB2 Front USB Connector JUSB1 ~USB 2.0 Bracket Chassis Intrusion Connector JCI1 Audio Amplifier Connector JAMP1PDIF-Out Connector JSPD1 Optional, for Hdmi ADD2 card only Clear Cmos Jumper JBAT1 JumperJBAT1 PCI Peripheral Component Interconnect Express Slot SlotsPage Bios Setup Press Del to enter Setup Entering SetupMain Menu Control KeysGetting Help General Help F1Menu Bar System Date AMI BIOS, Processor, System MemoryMain System TimeAdvanced CPU ConfigurationPeci Configure SATA#1 as IM-Q35 Mainboard IDE Configuration SATA#1 ConfigurationPrimary/Secondary/Third/Fourth/Fifth IDE Master/Slave Chassis Intrusion Super IO Configuration Serial Port 1 / 2 AddressSerial Port2 Mode Watch DogCPU/System Smart Fan Tolerance CPU/Systen Smart FAN ModeAcpi Configuration CPU/System Smart FAN TargetResume On RTC Alarm Bios Setup Suspend modeAcpi Version Features APM Configuration Resume On PME#Redirection After Bios Post IM-Q35 Mainboard Intel AMT Configuration Intel AMT SupportRemote Access Configuration Serial Port ModeUSB 2.0 Controller Mode Bios Setup Terminal TypeSredir Memory Display Delay USB Configuration Legacy USB SupportEmulation Type IM-Q35 Mainboard USB Mass Storage Reset DelayExcute TPM Command TPM Enable/Disable StatusWait For ‘F1’ If Error BootBoot Settings Configuration Quick Boot Bootup Num-LockRemovable Drives 1st Drive IM-Q35 Mainboard Boot Device Priority 1st Boot DeviceUser Password / Change User Password Supervisor Password / Change Supervisor PasswordSecurity Chipset North Bridge Configuration Initate Graphics AdapterInternal Graphics Mode Select Dvmt Mode SelectUSB 2.0 Controller Bios Setup DVMT/FIXED MemorySouth Bridge Chipset Configuration USB Functions GbE LAN BootME-IDER ME-HECIME-KT Exit Page System Resources Software code Sioidx equ 4EH SIODTAequ 4FH Watch Dog Timer SettingAMI Post Code Bootblock Initialization Code CheckpointsCdrom IM-Q35 Mainboard Bootblock Recovery Code CheckpointsPost Code Checkpoints Initializes Dmac -1 & DMAC-2 PCI Device Resource List