Intel IM-Q35 Series IM-Q35 Mainboard Intel AMT Configuration Intel AMT Support, Serial Port Mode

Page 51

IM-Q35 Mainboard

Intel AMT Configuration

Intel AMT Support

This setting allows you to enable/disable the Intel Active Management Technology(AMT) support.

Remote Access Configuration

Remote Access

This setting allows you to enable/disable remote access.

Serial port number

This setting specifies the serial port for console redirection.

Serial Port Mode

This setting allows you to select the serial port mode.

Flow Control

This item specivies how the transfer via the port is controlled. The setting must be the same on both the terminal and the server.

[None]

The port is operated without transfer control.

[XON/XOFF]

The port transfer control is carried out by software.

[CTS/RTS]

The port transfer control is carried out by hardware.

 

This mode must be supported by the cable.

Redirection After BIOS POST

This item specifies whether or not the console redirection is run after the Power-On Self Test (POST).

[Always]

Redirection is always active. (Some operating systems

 

may not work if this item is set to Always.)

[Boot Loader]

Redirection is only active during POST.

[Disabled]

Redirection is deactivated.

3-12

Image 51
Contents MS-9820 V1.X Mainboard IM-Q35 SeriesTechnical Support Copyright NoticeTrademarks Revision HistorySafety Instructions FCC-B Radio Frequency Interference Statement Micro-Star International MS-9820Weee Waste Electrical and Electronic Equipment Statement Page Vii Contents Page Product Overview Sata Mainboard SpecificationsLAN IDESlots Form FactorMounting Block Diagram IM-Q35 Mainboard Mini ITX Mainboard LayoutBoard Dimension Back Panel & I/O Shield Drawing Condition Power ConsumptionRFI Safety Compliance & MtbfPage Hardware Setup Quick Components Guide Introduction to LGA 775 CPU CPU Central Processing UnitCPU & Cooler Installation Lift the load lever up and open the load plate Locking switch Dual-Channel mode Population Rule MemoryDDR2 Volt Notch Installing Memory ModulesJPW1 Power SupplyATX 20-Pin System Power Connector JPWR1 ATX 12V Power Connector JPW1RS-232 Port Back PanelAudio Ports Hardware Setup USB PortConnectors IDE Connector IDE2IDE2 SATA4 SATA1 SATA3 SATA2 Serial ATA Connector SATA1 ~ SATA4JFP1 Fan Power Connectors CPUFAN1, SYSFAN1Front Panel Connector JFP1 CPUFAN1SYSFAN1JCOM1 Front Panel Audio Connector JAUD1RS-232 Port Connector Jcom JAUD1Front USB Connector JUSB1 ~ JUSB1 JUSB2USB 2.0 Bracket Audio Amplifier Connector JAMP1 Chassis Intrusion Connector JCI1PDIF-Out Connector JSPD1 Optional, for Hdmi ADD2 card only Jumper Clear Cmos Jumper JBAT1JBAT1 PCI Peripheral Component Interconnect Express Slot SlotsPage Bios Setup Press Del to enter Setup Entering SetupMain Menu Control KeysGetting Help General Help F1Menu Bar System Date AMI BIOS, Processor, System MemoryMain System TimeAdvanced CPU ConfigurationPeci IM-Q35 Mainboard IDE Configuration SATA#1 Configuration Configure SATA#1 asPrimary/Secondary/Third/Fourth/Fifth IDE Master/Slave Chassis Intrusion Super IO Configuration Serial Port 1 / 2 AddressSerial Port2 Mode Watch DogCPU/System Smart Fan Tolerance CPU/Systen Smart FAN ModeAcpi Configuration CPU/System Smart FAN TargetResume On RTC Alarm Bios Setup Suspend modeAcpi Version Features APM Configuration Resume On PME#Redirection After Bios Post IM-Q35 Mainboard Intel AMT Configuration Intel AMT SupportRemote Access Configuration Serial Port ModeUSB 2.0 Controller Mode Bios Setup Terminal TypeSredir Memory Display Delay USB Configuration Legacy USB SupportEmulation Type IM-Q35 Mainboard USB Mass Storage Reset DelayExcute TPM Command TPM Enable/Disable StatusWait For ‘F1’ If Error BootBoot Settings Configuration Quick Boot Bootup Num-LockRemovable Drives 1st Drive IM-Q35 Mainboard Boot Device Priority 1st Boot DeviceSupervisor Password / Change Supervisor Password User Password / Change User PasswordSecurity Chipset North Bridge Configuration Initate Graphics AdapterInternal Graphics Mode Select Dvmt Mode SelectUSB 2.0 Controller Bios Setup DVMT/FIXED MemorySouth Bridge Chipset Configuration USB Functions GbE LAN BootME-HECI ME-IDERME-KT Exit Page System Resources Software code Sioidx equ 4EH SIODTAequ 4FH Watch Dog Timer SettingAMI Post Code Bootblock Initialization Code CheckpointsCdrom IM-Q35 Mainboard Bootblock Recovery Code CheckpointsPost Code Checkpoints Initializes Dmac -1 & DMAC-2 PCI Device Resource List