Intel PCM-9387 user manual Connectors

Page 23

2.2 Connectors

On-board connectors link the PCM-9387 to external devices such as hard disk drives, a keyboard, or floppy drives. The table below lists the func- tion of each of the board’s connectors.

Table 2.8: Connectors

Label	Function

CN1	LVDS Connector

CN2	Audio Connector

CN3	ATX Power Connector

CN5	Internal USB connector (Channel 0,1)

CN6	Primary IDE connector

CN7	GPIO connector

CN8	COM2 connector

CN9	External USB connector (Channel2) Connector

CN10	HD LED & Power LED connector

CN11	SIR Connector

CN12	LAN Connector

CN13	Print Port connector

CN14	Keyboard /Mouse Connector

CN15	Fan Power connector

CN16	Power Switch connector

CN17	Inverter Power connector

CN18	CRT Connector

CN19	COM1 connector

CN21	CF Connector

CN22	PC/104 PLUS connector

CN23	DVI connector

11

Chapter2

Image 23

Contents User’s Manual PCM-9387Copyright Packing List Model No. List DescriptionAdditional Information and Assistance Page PCM-9387 User’s Manual Contents Chapter Chipset Software Installation Utility Integrated Peripherals Chapter Audio Setup Appendix D AT/ATX Power setting PCM-9387 User’s Manual Xii General Information Introduction FeaturesIntroduction 2 VGA/LVDS Interface SpecificationsStandard 3.5 Biscuit SBC Functions Mechanical and Environmental Ethernet InterfaceAudio Function Board layout DimensionsComponent Side Board layout dimensionsBoard layout DimensionsSolder Side Installation Jumpers JumpersJumper Location LCD Power Setting J6 Jumper SettingsAudio Power SelectorJ1 COM2 SettingCmos clear PCI VIO JP1Connectors ConnectorsJumpers and Connectors Drawing component side Locating ConnectorsConnectors solder side Setting Jumpers IDE, Cdrom hard drive connector CN6 Installing SO-DIMMCompactFlash CN21 Parallel port connector CN13Connecting the hard drive Solid State DiskPower connectors CN3 Keyboard and PS/2 mouse connector CN14Power & HDD LED Connector CN10 14 VGA/LCD/LVDS interface connections COM port connector CN8,CN19Audio interfaces CN2 15.1 100Base-T/1000Base-T connector CN12 Ethernet configurationWatchdog timer configuration USB connectors CN5,CN9Gpio General Purpose Input Output CN7 Chipset Software Installation Utility Ers Before you beginInstalling the CSI Utility PCM-9387 User’s Manual Page PCM-9387 User’s Manual Award Bios Setup Cmos RAM Auto-backup and Restore Award Bios Setup initial screen Entering SetupAdvanced Bios Features Standard Cmos Setup2 L1 & L2 Cache Quick Power On Self TestFirst/Second/Third/Other Boot Device Virus WarningTypematic Delay msec Boot UP Floppy SeekBoot Up NumLock Status Typematic Rate SettingOn-Chip Secondary PCI IDE IDE Master/Slave PIO/UDMA ModeIntegrated Peripherals MPS Version Control For OSUSB Controller IDE HDD Block ModeUart Mode Select IR Transmission DelayECP Mode Use DMA 14 UR2 Duplex ModeParallel Port Mode EPP Mode SelectAcpi function Power Management SetupPower-Supply Type Power ManagementPowerOn By Alarm HDD Power DownPowerOn By LAN PowerOn By ModemPCI Pirq A-D# PnP/PCI ConfigurationsPnP OS Installed Primary IDE 0 1 and Secondary IDE 04 PCI/VGA Palette Snoop Password SettingReset Configuration Data Resources controlled byExit Without Saving Save & Exit SetupPCI SVGA/LCD Setup Dual Independent Display Cmos setting for panel typeDisplay type Page Connections to LCD/Flat Panel CN1 Connections to Two Standard LCDsLG LM 150x06 1024x768 Lvds LCD Connections to AU M170EG01 CN1 AU M170EG01 1280x1024 TFT LCD @ 48bitInstallation of Windows 98/2000 Installation of the Svga DriverPage Double click setup and next into setup wizard Further Information PCM-9387 User’s Manual Audio Setup Before you begin Driver installationWindows 98 drivers Click yes to reboot your computer Ethernet Interface Installation for Windows Installation of Ethernet driverPage PCM-9387 User’s Manual Page Installation for Windows Page Choose Hardware Device Ethernet Controller Page PCM-9387 User’s Manual Further information PCM-9387 User’s Manual Programming the Gpio and Watchdog Timer Gpio Registers Appendix a Programming Gpio & Waterdog TimerSupported Gpio Register Gpio Example program-1 MOV DX,2EH MOV AL,AAH OUT DX,AL Watchdog programming MOV DX,2EH MOV AL,F6H OUT DX,AL MOV DX,2FH Pin Assignments Table B.2 Audio connector CN2 CPU Fan Power Connector CN15Audio Connector CN2 Table B.1 IR connector CN15Table B.4 Keyboard and mouse connector CN14 Main Power Connector CN3Table B.3 Main Power Connector CN3 Table B.5 IDE HDD connector CN6 IDE Hard Drive Connector CN6Table B.6 Parallel Port Connector CN13 Table B.8 USB Connector CN5 USB Connector CN5Table B.7 Power & HDD LED Connector CN10 Table B.9 LCD Inverter Backlight Conn CN17 LCD Inverter Backlight Connector CN17Table B.10 Lvds Connector CN1 Lvds Connector CN1Table B.11 COM2 RS-232/422/485 series port CompactFlash Card Connector CN21Table B.12 CompactFlash Card Connector CN21 11 COM2 RS232/422/485 series port CN8IR connetor CN11 Table B.13 IR Connector CN11MIO interface CN4 Table B.14 MIO connectorsCBE#1 PCI DVOBCLK# PCM-9387 User’s Manual System Assignments Table C.1 System I/O ports Appendix C System AssignmentsSystem I/O Ports Table C.3 DMA channel assignments 1st MB memory mapDMA channel assignments Table C.2 1st MB memory mapTable C.4 Interrupt assignments Interrupt assignmentsAT/ATX Power setting Table D.1 Power Connector Appendix D AT/ATX Power settingATX power supply diagram AT power supply diagram Mechanical Drawings Mechanical Drawings Appendix E Mechanical DrawingsFigure E.2 PCM-9387 Mech Drawing Solder Side PCM-9387 User’s Manual