Intel PCM-9387 user manual Installing SO-DIMM, IDE, Cdrom hard drive connector CN6

Page 27

2.5 Installing SO-DIMM

 

 

Module Key Aligned

 

 

With housing Key

 

2

Housing

 

 

 

 

Card Slot

PC Board

 

 

1

 

 

Module Tilted

 

3

Approximately 25

 

 

Module Latching

Ledge(TO Engage

Edge of Module)

The procedures for installing SODIMMs are described below. Please fol- low these steps carefully. You can install SDRAM memory modules using 200-pin SODIMMs (Small Outline Dual In-line Memory Modules).

1.Ensure that all power supplies to the system are switched off.

2.Tilt the SODIMM card approximately 25o above the board, and move it in the direction of the housing card slot. Make sure that the key in the module and the key in the housing are aligned.

3.Push the module into the socket until the module bottoms. There should be a slight insertion force to engage the module into the contacts.

2.6IDE, CDROM hard drive connector (CN6)

The board provides 1 IDE channels which you can attach up to two Enhanced Integrated Device Electronics hard disk drives or CDROM to the board’s internal controller. Its IDE controller uses a PCI interface. This advanced IDE controller supports faster data transfer, PIO mode 3, mode 4 and up to UDMA/33.

15

Chapter2

Image 27
Contents User’s Manual PCM-9387Copyright Packing List Model No. List DescriptionAdditional Information and Assistance Page PCM-9387 User’s Manual Contents Chapter Chipset Software Installation Utility Integrated Peripherals Chapter Audio Setup Appendix D AT/ATX Power setting PCM-9387 User’s Manual Xii General Information Features IntroductionIntroduction Specifications Standard 3.5 Biscuit SBC Functions2 VGA/LVDS Interface Ethernet Interface Audio FunctionMechanical and Environmental Board layout DimensionsComponent Side Board layout dimensionsBoard layout DimensionsSolder Side Installation Jumpers Jumper LocationJumpers LCD Power Setting J6 Jumper SettingsAudio Power SelectorJ1 COM2 SettingCmos clear PCI VIO JP1Connectors ConnectorsJumpers and Connectors Drawing component side Locating ConnectorsConnectors solder side Setting Jumpers IDE, Cdrom hard drive connector CN6 Installing SO-DIMMCompactFlash CN21 Parallel port connector CN13Connecting the hard drive Solid State DiskKeyboard and PS/2 mouse connector CN14 Power & HDD LED Connector CN10Power connectors CN3 COM port connector CN8,CN19 Audio interfaces CN214 VGA/LCD/LVDS interface connections 15.1 100Base-T/1000Base-T connector CN12 Ethernet configurationWatchdog timer configuration USB connectors CN5,CN9Gpio General Purpose Input Output CN7 Chipset Software Installation Utility Ers Before you beginInstalling the CSI Utility PCM-9387 User’s Manual Page PCM-9387 User’s Manual Award Bios Setup Cmos RAM Auto-backup and Restore Award Bios Setup initial screen Entering SetupAdvanced Bios Features Standard Cmos Setup2 L1 & L2 Cache Quick Power On Self TestFirst/Second/Third/Other Boot Device Virus WarningTypematic Delay msec Boot UP Floppy SeekBoot Up NumLock Status Typematic Rate SettingOn-Chip Secondary PCI IDE IDE Master/Slave PIO/UDMA ModeIntegrated Peripherals MPS Version Control For OSUSB Controller IDE HDD Block ModeUart Mode Select IR Transmission DelayECP Mode Use DMA 14 UR2 Duplex ModeParallel Port Mode EPP Mode SelectAcpi function Power Management SetupPower-Supply Type Power ManagementPowerOn By Alarm HDD Power DownPowerOn By LAN PowerOn By ModemPCI Pirq A-D# PnP/PCI ConfigurationsPnP OS Installed Primary IDE 0 1 and Secondary IDE 04 PCI/VGA Palette Snoop Password SettingReset Configuration Data Resources controlled byExit Without Saving Save & Exit SetupPCI SVGA/LCD Setup Cmos setting for panel type Display typeDual Independent Display Page Connections to Two Standard LCDs LG LM 150x06 1024x768 Lvds LCDConnections to LCD/Flat Panel CN1 Connections to AU M170EG01 CN1 AU M170EG01 1280x1024 TFT LCD @ 48bitInstallation of Windows 98/2000 Installation of the Svga DriverPage Double click setup and next into setup wizard Further Information PCM-9387 User’s Manual Audio Setup Before you begin Driver installationWindows 98 drivers Click yes to reboot your computer Ethernet Interface Installation for Windows Installation of Ethernet driverPage PCM-9387 User’s Manual Page Installation for Windows Page Choose Hardware Device Ethernet Controller Page PCM-9387 User’s Manual Further information PCM-9387 User’s Manual Programming the Gpio and Watchdog Timer Appendix a Programming Gpio & Waterdog Timer Supported Gpio RegisterGpio Registers Gpio Example program-1 MOV DX,2EH MOV AL,AAH OUT DX,AL Watchdog programming MOV DX,2EH MOV AL,F6H OUT DX,AL MOV DX,2FH Pin Assignments Table B.2 Audio connector CN2 CPU Fan Power Connector CN15Audio Connector CN2 Table B.1 IR connector CN15Main Power Connector CN3 Table B.3 Main Power Connector CN3Table B.4 Keyboard and mouse connector CN14 Table B.5 IDE HDD connector CN6 IDE Hard Drive Connector CN6Table B.6 Parallel Port Connector CN13 USB Connector CN5 Table B.7 Power & HDD LED Connector CN10Table B.8 USB Connector CN5 Table B.9 LCD Inverter Backlight Conn CN17 LCD Inverter Backlight Connector CN17Table B.10 Lvds Connector CN1 Lvds Connector CN1Table B.11 COM2 RS-232/422/485 series port CompactFlash Card Connector CN21Table B.12 CompactFlash Card Connector CN21 11 COM2 RS232/422/485 series port CN8IR connetor CN11 Table B.13 IR Connector CN11MIO interface CN4 Table B.14 MIO connectorsCBE#1 PCI DVOBCLK# PCM-9387 User’s Manual System Assignments Appendix C System Assignments System I/O PortsTable C.1 System I/O ports Table C.3 DMA channel assignments 1st MB memory mapDMA channel assignments Table C.2 1st MB memory mapTable C.4 Interrupt assignments Interrupt assignmentsAT/ATX Power setting Table D.1 Power Connector Appendix D AT/ATX Power settingATX power supply diagram AT power supply diagram Mechanical Drawings Mechanical Drawings Appendix E Mechanical DrawingsFigure E.2 PCM-9387 Mech Drawing Solder Side PCM-9387 User’s Manual