Intel DQ35MP manual Remove the Processor from the Protective Processor Cover

Page 37

Installing and Replacing Desktop Board Components

5.Remove the processor from the protective processor cover. Hold the processor only at the edges, being careful not to touch the bottom of the processor (see Figure 10). Do not discard the protective processor cover. Always replace the processor cover if the processor is removed from the socket.

Figure 10. Remove the Processor from the Protective Processor Cover

6.Hold the processor with your thumb and index fingers oriented as shown in

Figure 11. Make sure your fingers align to the socket cutouts (Figure 11, A). Align notches (Figure 11, B) with the socket (Figure 11, C). Lower the processor straight down without tilting or sliding it in the socket.

Figure 11. Install the Processor

37

Image 37
Contents Intel Desktop Board DQ35MP Product Guide FCC Declaration of Conformity Revision HistoryCanadian Department of Communications Compliance Statement DisclaimerIntended Audience PrefaceUse Only for Intended Applications Document OrganizationIntel Desktop Board DQ35MP Product Guide TerminologyTerm Description Contents Installing and Replacing Desktop Board Components Contents Configuring for RAID Intel Matrix Storage TechnologyTables Feature Summary Desktop Board FeaturesRelated Links Supported Operating Systems Desktop Board FeaturesDesktop Board DQ35MP Components Desktop Board ComponentsLabel Description Main Memory ProcessorType Timing Intel Q35 Express ChipsetIntel GMA 3100 Graphics Controller Intel Q35 Graphics SubsystemAudio Subsystem LAN Subsystem Legacy Input/Output I/O ControllerIntel Active Management Technology Intel AMT RJ-45 LAN Connector LEDsLED Color LED State Indicates Intel AMT Status Indicator Intel AMT Status IndicatorLED State Indicates Enhanced IDE Interface Hi-Speed USB 2.0 SupportSerial ATA Serial ATA RAIDSerial ATA and IDE Auto Configuration Intel Rapid Recover TechnologyPCI* and PCI Express* Auto Configuration ExpandabilityHard Disk Drive Passwords Security PasswordsTrusted Platform Module TPM Hardware Management FeaturesHardware Monitoring and Fan Speed Control Power Management FeaturesChassis Intrusion Hardware Support AcpiLAN Wake Capabilities +5 V Standby Power Indicator Speaker BatteryReal-Time Clock Energy STAR* CapableIntel Desktop Board DQ35MP Product Guide Before You Begin Installing and Replacing Desktop Board ComponentsPrevent Power Supply Overload Installation PrecautionsObserve Safety and Regulatory Requirements Installing and Replacing Desktop Board Components Installing the I/O ShieldDesktop Board DQ35MP Mounting Screw Hole Locations Installing and Removing the Desktop BoardInstalling a Processor Installing and Removing a ProcessorLift the Load Plate Remove the Processor from the Protective Processor Cover Close the Load Plate Installing the Processor Fan Heat SinkConnecting the Processor Fan Heat Sink Cable Removing the Processor Installing and Removing MemoryDual Channel Memory Configuration with Two DIMMs Guidelines for Dual Channel Memory ConfigurationThree DIMMs Use DDR2 DIMMs Installing DIMMsInstalling a Dimm Removing DIMMs Installing a PCI Express x16 Card Installing and Removing a PCI Express x16 CardRemoving a PCI Express x16 Card Removing the PCI Express x16 CardConnecting the IDE Cable Connecting the IDE Cable Connecting a Serial ATA Cable Connecting the Serial ATA Sata CablesInternal Headers Connecting to the Internal HeadersHD Audio Link Header Signal Names Connecting to the HD Audio Link HeaderFront Panel Intel High Definition Audio Header Signal Names Pin Signal NameConnecting to the Serial Port Header Connecting to the Chassis Intrusion HeaderSerial Port Header Signal Names Chassis Intrusion HeaderConnecting to the Front Panel Header Connecting to the Alternate Front Panel Power LED HeaderAlternate Front Panel Power LED Header Front Panel HeaderConnecting to the USB 2.0 Headers Connecting to the Audio SystemUSB 2.0 Header Signal Names USB Port aConnecting Chassis Fan Cables Connecting Chassis Fan and Power Supply CablesConnecting Power Supply Cables Connecting Supply Power CablesLocation of the Bios Configuration Jumper Block Setting the Bios Configuration JumperJumper Setting Mode Description Jumper Settings for the Bios Setup Program ModesClearing Bios Security Passwords Clearing or Changing PasswordsClearing or Changing Hard Disk Drive Passwords Replacing the BatteryViktigt Προσοχή Внимание Installing and Replacing Desktop Board Components Removing the Battery Updating the Bios with the Intel Express Bios Update Utility Updating the BiosUpdating the Bios with the ISO Image Bios Update File Obtaining the Bios Update FileUpdating the Bios Updating the Bios with the Iflash Memory Update UtilityRecovering the Bios Configuring the Bios for Intel Matrix Storage Technology Configuring for RAID Intel Matrix Storage TechnologyCreating Your RAID Set Setting Up a RAID Ready System Enabling Intel Rapid Recover Technology Configuring for Intel Rapid Recover TechnologyGo to Advanced Drive Configuration Creating a Recovery Volume Using the RAID Option Creating a Recovery VolumeSelect Protect data using Intel Rapid Recover Technology Mounting the Recovery Disk Disk Synchronization ModeConfiguring for Intel Rapid Recovery Technology Select Access Recovery Drive Files Bios Beep Codes Error Messages and IndicatorsBios Error Messages Bios Error MessagesIntel Desktop Board DQ35MP Product Guide Place Battery Marking Safety StandardsSafety Standards Regulatory ComplianceEuropean Union Declaration of Conformity Statement Recycling Considerations Product Ecology StatementsRegulatory Compliance Español DeutschFrançais MalayPortuguese Lead-Free Desktop BoardRussian TürkçeLead-Free Board Markings EMC Regulations EMC RegulationsEnsure Electromagnetic Compatibility EMC Compliance Board-Level Certification Markings Product CertificationsProduct Certification Markings Europe Chassis and Component Certifications