Intel AIMB-744 user manual Safety Precautions

Page 24

1.7 Safety Precautions

Warning!

Always completely disconnect the power cord

 

from your chassis whenever you work with the

 

hardware. Do not make connections while the

 

power is on. Sensitive electronic components

 

can be damaged by sudden power surges. Only

 

experienced electronics personnel should open

 

the PC chassis.

Caution!

Always ground yourself to remove any static

 

charge before touching the motherboard. Mod-

 

ern electronic devices are very sensitive to

 

static electric charges. As a safety precaution,

 

use a grounding wrist strap at all times. Place

 

all electronic components on a static-dissipative

 

surface or in a static-shielded bag when they

 

are not in the chassis.

Caution!

The computer is provided with a battery-pow-

 

ered Real-time Clock circuit. There is a danger

 

of explosion if battery is incorrectly replaced.

 

Replace only with same or equivalent type rec-

 

ommended by the manufacturer. Discard used

 

batteries according to manufacturer's instruc-

 

tions.

Caution!

There is a danger of a new battery exploding if

 

it is incorrectly installed. Do not attempt to

 

recharge, force open, or heat the battery.

 

Replace the battery only with the same or

 

equivalent type recommended by the manufac-

 

turer. Discard used batteries according to the

 

manufacturer’s instructions.

AIMB-744 User’s Manual

10

Image 24
Contents AIMB-744 Copyright Notice Advantech customer services Message to the CustomerBrand Size Speed Type Memory Product warranty AIMB-744 comparison tableInitial Inspection Release NoteContents Chapter Award Bios Setup Advanced Chipset Features PnP/PCI Configurations Chapter Chipset Software Install Utility CPU/System Fan Power Conn CN14/15/37 PCI Bus Map 105 AIMB-744 User’s Manual Xiv General Information Hardware Configuration IntroductionFeatures SpecificationsSystem Memory Input/OutputAGP interface Ethernet LANJumpers and Connectors Industrial featuresMechanical and environmental specifications LabelConnectors FunctionSA0 Board Layout Jumper and Connector Locations Jumper and Connector locationsAIMB-744 Block Diagram Tel 82875PSafety Precautions Page Jumper Settings How to set jumpersWatchdog timer output J2 Function Jumper SettingWatchdog timer output J2 PCI-X 33/66Mhz selection J5 & J6System Memory PCI-X slots 3.3V/5V selection J8CPU FSB and memory speed Memory Installation Procedures Dual channel configurationProcessor Installation Cache MemoryConnecting Peripherals Primary CN1 and Secondary CN2 IDE Connec Tors Floppy Drive Connector CN3 Parallel Port CN4USB Ports CN6 shared with CN32 Serial Ports COM1 CN9 COM2 CN38 COM3 CN10 COM4 COM23External Keyboard Connector CN12 PS/2 Keyboard and Mouse Conn CN11CPU Fan Connector CN14 System FAN connector CN15 and CN37Front Panel Connectors CN16, 17, 18, 19, 21&29 Power LED and Keyboard Lock CN16Reset CN18 ATX soft power switch CN21PS/2 or ATX power supply LED status External speaker CN1712 H/W Monitor Alarm CN22 SM Bus Connector CN29USB and LAN ports CN31 and CN32 Line Out, Mic in connector CN55 Audio input from CD-ROM CD in CN56Aux Line-In connector AUX in CN57 Front Panel audio connector FP Audio CN5918 8-pin Alarm Board Connector CN62 Case Open Connector CN64Serial ATA interface SA0 and SA1 Connecting to SNMP-1000 remote manager Auxiliary 4-pin power connector ATX1Award Bios Setup Cmos RAM Auto-backup and Restore Entering Setup Standard Cmos SetupAdvanced Bios Features Hard Disk Boot PriorityVirus Warning CPU L1 & L2 CacheQuick Power On Self Test First/Second/Third Boot DeviceBoot Other Device Boot UP Floppy SeekAdvanced Chipset Features Apic ModeSecurity Option MPS Version Control For OSActive to Precharge Delay Dram RAS# to CAS# DelayDram Timing Selectable CAS Latency TimeSystem Bios Cacheable Video Bios CacheableDelay Prior to Thermal Memory Hole At 15M-16MIntegrated Peripherals Integrated peripheralsIDE HDD Block Mode Serial ATA Port0/Port1 ModeOn-Chip IDE Device On-Chip Serial ATAOnboard LAN Boot ROM USB ControllerUSB 2.0 Controller USB Keyboard/Mouse SupportUart Mode Select Parallel Port ModeEPP Mode Select Onboard FDC ControllerPower Management Setup ECP Mode Use DMAPwron After PWR-Fail Acpi functionPower Management Video Off MethodVideo Off In Suspend Suspend TypePnP/PCI Configurations PC Health Status Password Setting Spread Spectrum ControlSave & Exit Setup Exit Without SavingChipset Software Installation Utility Chipset Software Install Utility Before you beginWindows XP Driver Setup AIMB-744 User’s Manual Page AIMB-744 User’s Manual LAN Configuration Introduction Installation Win XP Driver Setup Intel 82547/41AIMB-744 User’s Manual Page AIMB-744 User’s Manual Onboard Security Setup Introduction Windows XP Driver Setup Click Next when you see the following message Page Using the OBS Hardware Doctor Utility Page AIMB-744 User’s Manual Programming the Watchdog Timer Programming the Watchdog Timer Watchdog timer overviewReset/ Interrupt selection Programming the Watchdog TimerAppendixA Address of register 2E Attribute Example Program Set timeout interval as 10 seconds and start counting AppendixA AIMB-744 User’s Manual AppendixA AIMB-744 User’s Manual Pin Assignments IDE Hard Drive Connector CN1, CN2 Table B.1 IDE hard drive connector CN1, CN2 Pin SignalTable B.2 Floppy drive connector CN3 Pin Signal Parallel Port Connector CN4 Table B.3 Parallel port connector CN4 Pin SignalUSB Connector CN6 shared with CN32 Table B.5 COM1/2 RS-232 serial port CN9/38 Pin SignalCOM1/2/3/4 RS-232 Serial Port Interface CN9/10/ 23/38 COM3/4 serial port connector CN10/23 Table B.6 Keyboard and mouse connector CN11 Pin SignalTable B.7 COM3/4 serial port connector CN10/23 Pin Signal Keyboard and Mouse Connnector CN11CPU/System Fan Power Conn CN14/15/37 Table B.8 External keyboard connector CN12 Pin SignalTable B.9 CPU/System Fan Power Conn CN14/15/37 Power LED CN16 External Speaker Connector CN17Table B.10 Power LED and keylock conn CN16 Pin Function Table B.11 External Speaker Connector CN17Reset Connector CN18 HDD LED Connector CN19Table B.12 Reset connector CN18 Pin Signal Table B.13 HDD LED connector CN19ATX Soft Power Switch CN21 Table B.14 ATX soft power switch CN21 Pin Signal15 H/W Monitor Alarm CN22 SM Bus Connector CN2917 USB/LAN ports CN31 and CN32 Table B.19 Audio in from CD-ROM CD in CN56 Pin Signal Table B.18 Ethernet 10/100Base-T RJ-45 portTable B.20 Aux Line-In connector AUX in CN57 Table B.21 Front audio conn FP Audio CN59 Pin Signal23 8-pin Alarm Board Connector CN62 Table B.22 Case Open Connector CN64Table B.23 8-pin Alarm Board Connector CN62 Pin Signal System I/O Ports Table B.24 System I/O ports Addr. range Hex DeviceDMA Channel Assignments Interrupt AssignmentsTable B.25 DMA channel assignments Channel Function 27 1st MB Memory Map PCI Bus MapPCI-X bus map AIMB-744 User’s Manual