Intel GA-945P-DS3/S3 user manual FDD Floppy Connector, IDE1 IDE Connector

Page 21

7)FDD (Floppy Connector)

The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360 KB, 720 KB, 1.2 MB, 1.44 MB and 2.88 MB. Before attaching the FDD cable, please take note of the foolproof groove in the FDD connector.

33

1

34

2

8)IDE1 (IDE Connector)

An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device). Before attaching the IDE cable, please take note of the foolproof groove in the IDE connector.

2

40

1

39

English

- 21 -

Hardware Installation

Image 21
Contents GA-945P-DS3/S3 Motherboard Product Manual Classification CopyrightTable of Contents Install Drivers Item Checklist GA-945P-DS3/GA-945P-S3 Motherboard Layout Block Diagram Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your ComputerCPU Feature SummaryMbit flash ROM Installation of the CPU Installation of the CPU and CPU CoolerInstallation of the CPU Cooler Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Connectors Introduction ATX12V/ATX Power Connector Nbfan Chip Fan Power Connector 5 Cpufan / Sysfan / Pwrfan Cooler Fan Power ConnectorIDE1 IDE Connector FDD Floppy ConnectorPwrled SATAII0/1/2/3 Sata 3Gb/s ConnectorFpanel Front Panel Jumper Faudio Front Audio Connector Spdifio S/PDIF In/Out Connector Cdin CD in ConnectorCI Chassis Intrusion, Case Open USB1 / FUSB2 Front USB ConnectorClrcmos Clear Cmos English Main Menu Status Page Setup Menu / Option Page Setup MenuMain Menu For example GA-945P-DS3 Bios Ver. F2c „ Advanced Bios Features „ Standard Cmos Features„ Power Management Setup „ PnP/PCI ConfigurationsTime Standard Cmos FeaturesIDE Channel 0 Master/Slave IDE Channel 2, 3 Master/SlaveDrive a Floppy 3 Mode Support for Japan AreaHalt on MemoryHard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Password CheckCPU Hyper-Threading Note HDD S.M.A.R.T. CapabilityLimit Cpuid Max. to 3Note No-Execute Memory ProtectNoteSmart LAN Integrated PeripheralsUSB 2.0 Controller Smart LAN LAN Cable Diagnostic FunctionUSB Keyboard Support USB Mouse SupportParallel Port Mode OnBoard LAN Boot ROMOnboard Serial Port Onboard Parallel PortECP Mode Use DMA Power Management SetupPower On By Keyboard Power On By MouseKB Power on Password AC Back FunctionPCI1 IRQ Assignment PnP/PCI ConfigurationsPC Health Status CPU Smart FAN Control CPU Smart FAN ModeCPU Clock Ratio Note MB Intelligent TweakerM.I.TRobust Graphics Booster A.2CPU Host Clock Control FSB1333 Core CPUCPU Host Frequency Mhz PCI Express Frequency MhzLoad Optimized Defaults Load Fail-Safe DefaultsSet Supervisor/User Password Exit Without Saving Save & Exit SetupInstall Chipset Drivers Install DriversDriver CD Information Software ApplicationsContact Us Hardware InformationEnglish Unique Software Utilities EasyTune 5 IntroductionUser Interface Overview How to use the Xpress Recovery2 Xpress Recovery2 IntroductionBoot from CD/DVD F9 Xpress Recovery2 System requirementsMain Screen of Xpress Recovery2 PrecautionsLimitations Updating the Bios Flash Bios Method IntroductionMethod 1 Q-FlashTM Before UseCopy Bios completed Pass Please press any key to continue Methods and steps Method 2 @BIOSTM UtilityEnglish 4 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and SettingsChannel Audio Setup English English Sound Effect Configuration Troubleshooting English English English English Taiwan Headquarters Contact UsGigabyte Global Service System